Coin #1 Value dEn 1
This option allows the owner to set a specific numerical value for
a coin entered. For example, in the United States the coin value
for one quarter would be measured in cents (25). Therefore, the
coin value entered for one quarter would be 00025.
If the Vend Price 1 is set for “.75”, and the Coin Value is set for
00025, the vend price displayed will decrease by 0.25 for each
coin entered and 3 coins will need to be entered to satisfy the
vend price.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until dEn 1 appears in the
display. Press the START (enter) keypad.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Coin #2 Value dEn 2
This option allows the owner to set a specific numerical value for
a coin entered when using the dual coin drop. For example, the
coin value for a dollar coin would be measured in cents (1.00).
Therefore, the coin value entered for one dollar coin would be
00100.
If the Vend Price #1 AtS 1 (option 1) is set for "2.00", and the
Coin Value is set for 00100, the vend price displayed will de-
crease by 1.00 for each dollar coin entered and 2 coins will need
to be entered to satisfy the vend price.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until dEn 2 appears in the
display. Press the START (enter) keypad.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Start Pulse Value PLSE
This option allows the owner to program the value of the Start
Pulse if used for multiple pulses with an after-market central card
reader or pay system.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3. Press the Delicates Bulky (∧) or the Cold (∨) keypad to scroll
through the programmable options until PLSE appears in the
display. Press the START (enter) keypad.
4. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
5. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
50 Part No. F8615401ENR4
To Next Page
Loading...
