Temperature Fahrenheit/Celsius (Heat
Models) tP F C
This option allows the owner to set whether the display units for
temperature will be shown in Fahrenheit or Celsius.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3.
Press the Delicates Bulky (∧) or the Cold (∨) keypad until tP
F C appears in the display.
4.
When tP F C appears in the display, press the keypad. A
setting will appear in the display. This setting (found below)
corresponds to the current Temperature (Fahrenheit/Celsius)
setting.
CELSiU = Celsius
FAHrEn = Fahrenheit
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to
change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Hot Water Temperature (Heat Models)
FL Hot
This option allows the owner to program the hot water tempera-
tures.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3.
Press the Delicates Bulky (∧) or the Cold (∨) keypad until FL
Hot appears in the display.
4. When the desired option appears in the display, press the
START (enter) keypad. A number will appear in the display.
This number corresponds to the current Hot Water Tempera-
ture value.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the current water temperature value to the
desired water temperature value.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Warm Water Temperature (Heat Models)
FL HC
This option allows the owner to program the warm water temper-
atures.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3.
Press the Delicates Bulky (∧) or the Cold (∨) keypad until FL
HC appears in the display.
4. When the desired option appears in the display, press the
START (enter) keypad. A number will appear in the display.
This number corresponds to the current Warm Water Temper-
ature value.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the current water temperature value to the
desired water temperature value.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cold Water Temperature (Heat Models)
FL CLd
This option allows the owner to program the cold water tempera-
tures.
1. Control must be in Manual Mode. Refer to Entering the Man-
ual Mode.
2. Press the Delicates Bulky (∧) or the Cold (∨) keypad until
Prog appears in the display. Press the START (enter) keypad
and AtS 1 will appear in the display.
3.
Press the Delicates Bulky (∧) or the Cold (∨) keypad until FL
CLd appears in the display.
4. When the desired option appears in the display, press the
START (enter) keypad. A number will appear in the display.
This number corresponds to the current Cold Water Tempera-
ture value.
5. Press the Delicates Bulky (∧) or the Cold (∨) keypad to in-
crease or decrease the current water temperature value to the
desired water temperature value.
NOTE: To go back to the current programmable op-
tion without changing the value of the active digit,
press the Warm (<) keypad.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
59 Part No. F8615401ENR4
To Next Page
Loading...
