Amberg Technologies GRP System FX

To Next Page

To Previous Page

Safety Directions User manual

Figure 15. Labelling of Profiler FX and GNSS pole

Figure 16. Labelling of Battery Column GBC 3010 and Battery module GEB 3010

Main Page

Table of Contents3
User Manual for the GRP System FX7
Introduction9
Symbols9
How to Use this Manual9
Product Identification9
Product Description10
Grp 100011
Grp 300011
Vms 100012
Vms 300012
Automatic Tribrach GAD12
Grp 500013
IMS Relative13
Ims 100014
Ims 300014
Ims 500015
Supported Instruments and Components15
Total Station for Georeferencing of GRP System FX15
GNSS System for Georeferencing of GRP System FX16
High-Speed Laser Scanner for the Configuration GRP/IMS 500016
Radio Modem for the Communication between Track Trolley and Total Station17
Trademarks17
Available Documentation17
Principle of Measurement and Terminology17
Relative Survey18
Absolute Survey18
Stop&Go Function (Static Measurements)18
Kinematic Measurements18
System Components19
Standard Accessories26
Compliance with Instructions and Plausability Checks by the User29
Safety Directions31
Use of Instrument31
Intended Use of Instrument31
Prohibited Uses31
Limits of Use32
Prohibited Modification32
Danger Working Within the Track Neighbourhood32
Danger from the Distance Measurement Lasers32
Other Dangers32
Avoid Changes of Geometric Trolley Parameters33
Responsibilities33
Manufacturer of the Product33
Manufacturers of Non Amberg Technologies Accessories33
Person in Charge of the Product33
International Warranty34
Software License Agreement (EULA)34
Hazards of Use34
Laser Classification37
Electromagnetic Compatibility (EMC)37
FCC Statement (Applicable in U.S.)38
Labelling39
Assembly, Installation, Start up43
Assembly of the Track Trolley TGS FX43
Cables and Connections for TGS FX44
External Sockets44
Internal Sockets45
Installation of the Prism Column GPC 10045
Installation of the Profiler FX45
Installation of the Height Adaptor GHA 20046
Installation of Additional Components for Use in Absolute Mode (Leica TPS System)46
On the Track Trolley TGS FX46
Total Station Leica TPS47
Installation of GNSS System48
Installation of GNSS Antenna48
Cable Connections48
Installation of High-Speed Laser48
Installation of the Adaptor Plate on the High-Speed Laser Scanner48
Installation of the Battery Column and the Scanner50
Cable Connections50
Exchange of the Scanner Battery GEB 5000 / GEB 501050
Connection Schemes51
GRP Relative / GRP 100051
Grp 300052
GRP 5000 with High-Speed Laser Scanner52
IMS 1000 with Leica Robotic Tachymeter and AMU 103053
IMS 3000 with Profiler FX and AMU 103054
IMS 5000 with High-Speed Laser Scanner with AMU 103055
IMS 1000 with Leica Robotic Tachymeter and AMU 203056
IMS 3000 with Profiler FX and AMU 203057
IMS 5000 with High-Speed Laser Scanner with AMU 203058
IMS Relative and AMU 201059
IMS 1000 with Leica Robotic Tachymeter and AMU 201060
IMS 3000 with Profiler FX and AMU 201061
GRP/IMS 1000/3000/5000 with GNSS62
Vms 300063
Grp Tsc / Grp Tsc64
Software Installation64
Operation65
Track Trolley TGS FX65
Switching on65
Coordinate System of TGS FX65
Sign Rules Super Elevation (Cant)65
Stationing66
Profiler FX66
Operation66
Switching on67
Information on the Display67
Measurement of a Specific Point67
Distance Measurement68
Display Brightness68
Distance Unit68
Angle Unit68
Displayed Coordinate System68
Standby Mode68
Switching off68
Communication Parameter68
Trouble-Shooting68
Laser Classification69
High-Speed Laser Scanner70
Laser Classification71
Switching on71
Switching off71
Problem Solving71
Inertial Measurement Technology72
Absolute Positioning with the Total Station74
Selection of the Prism74
Radio Modem Communication74
Absolute Positioning with GNSS74
Setting up the Total Station74
Optimal Survey Geometry74
Atmospheric Influences74
Control Points74
Measurement on the Track74
Commissioning of the Trolley on the Track74
Move to the Measuring Position75
Rotating the Trolley75
Interruption of Measurement75
End of Measurement75
Handling the Trolley TGS FX or TSC off the Track76
Battery Life76
Battery Charging78
Maintenance, Checking and Adjustment79
System Maintenance79
Cleaning79
Checking and Adjustment Concept79
Check and Adjustment of Track Trolley Geometry79
Check and Adjustment of Cant Sensor80
Adjustment80
Check and Adjustment of Gauge Sensor80
Checking and Adjustment of Odometer80
Check and Adjustment of the Automatic Tribrach GAD81
Troubleshooting83
Repair85
Exchange of Gauge Measuring Wheel85
Exchange of Wheels85
Single Wheel85
Wheel on Two-Wheel Part86
Exchange of Brake Block86
Storage of the System86
Packing and Transportation89
Disposal91
Technical Data93
Trolley TGS FX93
Batteries93
Battery System GBS 101093
Battery Column GBC 3010 with Battery Module GEB 301094
Battery Column GBC 5000 with Battery Module GEB 5000 / GEB 501094
Profiler FX95
General95
Disto Den-10-50095
Transport Case95
Amberg Measuring Unit (AMU)96
Inertial Measurement Module AMU 103096
Inertial Measurement Module AMU 201096
Inertial Measurement Module AMU 203096
Control Computer97
Cables97
Environmental Specifications99
Speed of Measurement99
Time Need to Clear Track99
Weight100
System Weight100
Weights Per Handle101
Construction Gauge According UIC105
Wear Parts106
Certificates109
Declaration of Identity109
Declaration of Conformity GRP System FX110
ISO 9001:2008 Zertifikation111

Amberg Technologies GRP System FX - Page 40

Table of Contents