ASL INTERCOM VAR4 - 22 VAR Router Software Update

To Next Page

To Previous Page

VAR4 / VAR12 / VAR20 - Operation Manual

Page 297 of 308

sue: 03 complete, approved

22 VAR Router Software Update

The Update tool is used to download DVA messages and to update the VAR Router software (operating

system and DSP code). Please refer to the Update tool documentation.

Main Page

Default Chapter3
- Table of Contents3
1 Introduction9
- About this Document9
- VAR Router SW Version9
2 VAR Router Operation10
- VAR Router Front Panel10
  - Indicators10
  - Controls11
- Responding to Fault Indications13
  - Records13
  - Action Following a Fault13
- Navigating the Menus14
- Conventions Used in this Manual15
- Menu Map of Functions16
3 Typical Configuration Process18
4 Accessing the VAR Router20
- Initialisation20
- Logging on21
- Logging off21
- Changing the System Access Code22
5 VAR Router Configuration23
- VAR Router Operation Mode23
- Var ID41
- VAR Router Name41
- System Date / Time42
- Temperature43
- Asynchronous Port43
- Emergency Sounder Operation44
- Remote Fault Output Configuration44
- Host Protocol Configuration46
- Configuration Data50
  - Configuration Data View50
  - Clearing Configuration Data and Restoring to Default Settings50
- VAR Router Software Versions51
6 ASL Amplifier Mainframe Commissioning52
- Detecting Frames Using 'Learn' Mode52
- Viewing Configured Mainframes54
  - Verbose View54
  - Terse View55
- Mainframe Commissioning56
7 MIC/Line Input Configuration70
- MIC/Line Input Type Configuration73
- Parameters Common to All MIC/Line Input Types75
- Paging Microphone and Zoned Fire Microphone Specifics98
- Single Button Microphone Specific Configuration135
  - PTT Button Zone Selection Configuration135
  - PTT Button Cough Timeout Configuration137
8 DVA Input Configuration139
- DVA Input Gain Configuration139
- DVA Input Relative Gain Configuration140
- DVA Input Priority Configuration141
- DVA Input Emergency Class143
- DVA Input Name Configuration145
- DVA Input Ambient Noise Sensor (ANS) Configuration146
9 Background Music Configuration148
- Music Input Configuration149
- Contact Music Selector Configuration158
10 Mute Input Configuration160
- Mute Input Emergency Class160
- Mute Input Priority Set-Up161
11 Test Tone Input Configuration163
- Test Tone Type Configuration164
- Test Tone Input Gain Configuration164
- Test Tone Input Priority Set-Up165
12 Output Configuration167
- Gain Configuration167
- Equalisation Configuration168
- Ambient Noise Sensor (ANS) Configuration170
  - Enabling/Disabling the ANS and Setting the Attack Time172
  - Configuring the ANS Range173
- Surveillance Tone Generation Configuration175
- Override Gain Configuration177
- Name Configuration178
13 Induction Loop Configuration180
- Setting the VAR Router to Support Induction Loop182
- Induction Loop Output Gain Configuration183
- Induction Loop Output Surveillance Tone Generation Configuration184
- Induction Loop Output Override Gain Configuration186
- Induction Loop Output Name Configuration187
- Induction Loop Parameter Configuration188
14 Contact Configuration193
- Configuring a Contact as Unused194
- Configuring a Contact for Routing196
- Configuring a Contact as an External Alarm Input212
- Configuring a Contact as Remote Fault Accept215
15 Permanent Route Configuration217
16 ASL BMB01 Remote I/O Expander Configuration219
- Remote I/O Unit RS485 Bus Configuration219
- Remote I/O Unit Analogue Input Configuration221
- Remote I/O Unit Digital Input (Contact) Configuration236
- Remote I/O Unit Digital Output Configuration256
17 Night Time Volume Control259
- Enabling/Disabling the Night Time Volume Control259
- Setting the Night Time Volume Control Active Time259
- Configuring the Maximum Output Level260
- Configuring the Affected Inputs260
18 Testing262
- Lamp and Sounder Testing262
- Monitoring263
- Amplifier Changeover Testing268
- Mainframe Status269
- Amplifier Status274
19 PC Configuration Tool280
- Connection280
- Starting a New Configuration280
- Loading the Configuration from the Unit280
- Loading the Configuration from a File281
- Saving the Configuration as Text File281
- Applying Changes to the Unit281
20 Fault Monitoring282
- Current Fault Status283
- Fault Acceptance283
- Fault Clearance283
- Fault Log284
- Fault Codes and Suggested Actions286
21 Maintenance293
- Training293
- Records293
- Maintenance Instructions294
  - Routine Maintenance294
  - Corrective Maintenance296
    - Action by the User after any Fire (Whether Detected Automatically or Not)296
    - Action Following a Fault296
22 VAR Router Software Update297
23 Manual Settings298
- Manual Restoration of Default Settings298
- Fault Clear Access Level301
24 Safety and Precautions302
- Environmental302
- Esd302
- Emc302
- Lithium Battery302
- Electrical Safety302
- Unpacking and Handling302
  - Packing for Return for Repair303
25 Reference Documents304
26 Index305
- Service and Warranty307

ASL INTERCOM VAR4 - 22 VAR Router Software Update

Table of Contents