Breas Nippy 4 - Page 152

150
Index
Doc. 006553 M-6
Operating conditions
specifications. . .. .. .. ... . .... .. .. ..117
Operator’s position
audible range .. . .. ... . ... . .. .. .. ... . 80
Oxygen
safety information. . . ... . ... . .. .. ...23
usage. .. ... . .. .. ... . .. .... .. .. ... . ...23
Oxygen inlet
position. ... . .. .... .. .. ... . .. .. .. ... . 32
specification . .. .. .. .. ... . .... .. .. ..117
P
Part numbers
main components .. .. ... . .... .. .. .. 25
Pathway
internal disinfection. . ... . .... .. .. .112
Patient air filters
clean and replace .. .. ... . .. .. ... . ..112
Patient air outlet
position. ... . .. .... .. .. ... . .. .. .. ... . 28
Patient circuit
connect. .. .. .. ... . .... .. .. ... . .. .. .. 38
safety information. . . ... . ... . .. .. ...18
Patient settings
adjust . . ... . .... .. .. .. .... .. .. ... . ...40
Patients
change . ... . ... . .. .. .. ... . .... .. .. ..114
Perform pre-use test .. . .. .. ... . ... . .. .40
Placement . .. .. .. ... . .. .. ... . .... .. .. .. 35
inspect. ... . .... .. .. .. ... . .. .. ... . ...39
Pneumatic diagram
leakage circuit (single limb) . .. .. ..116
single limb circuit ... .. .. ... . .... ..116
Poor SpO
2
Signal alarm ... . ... . .. .. .. 98
Position
operator, audible range ... .. . .. ... . 80
Power Failure Alarm alarm .. . . ... . ...95
Power supply specification .. . .. .. ...117
Pre-Use Test
Failure . .. .. .... .. .. .. ... . .. .. ... . ...41
Product label. .. .. .. .. .. ... . .... .. .. ...32
Profiles
about .. . ... . .. .. .. ... . ... . .. .. .. ... . 49
delivery settings .. . .. .... .. .. ... . ..128
select. .. . ... . .. .... .. .. ... . .... .. .. .. 49
Protective cover. .. .. ... . .... .. .. .. ... . 70
R
Ramp time . . .. ... . .. .. .. ... . .... .. .. .. 53
Rebreathing alarm .. .. .. ... . .. .. ... . .. 91
Reference
Icon.. .. .. .. .... .. .. ... . .. .. .. ... . ...11
Regular maintenance. .. .. .. .. .. ... . ..114
Remote alarm
using. .. .. .. .. .. ... . .... .. .. .. ... . .. .69
Remote Start/Stop. . .... .. .. ... . .... .. 70
Repair . ... . .... .. .. .. ... . .. .. ... . .... .114
Reset alarm.. . ... . .. .. ... . ... . .. .. .. ...80
Rise time . .. .. ... . .... .. .. ... . .. .. .. ...51
S
Safety information
cleaning and maintenance. .. .. .. ...22
environmental conditions. .. .... .. .17
filters . .. ... . .. .. .. ... . .... .. .. ... . .. 17
humidification. ... . ... . .. .. .. ... . ...21
oxygen.. .. .. ... . .. .. .. ... . .... .. .. .. 23
patient circuit.. .. .. ... . .. .. .. ... . ...18
Safety label . .. ... . .... .. .. ... . .. .. .. ...32
Service.. . .. .... .. .. .. ... . .. .. ... . .... .114
Settings
at delivery .. .. .. .. .... .. .. ... . .. .. .128
specification . .. .. .. ... . .... .. .. .. ..117
Side panel . ... . .... .. .. .. ... . .. .. ... . .. 28
Sigh
settings .. .. .. .. .... .. .. ... . .. .. .. ...51
Single limb circuit
pneumatic diagram. .. . ... . .. ... . ..116
Sleep mode.. .. ... . .. .... .. .. ... . .... .. 45
Sound level
specification . .. .. .. ... . .... .. .. .. ..117
Specifications
dimension .. . .. ... . .. .. ... . .. .... ..117
environmental conditions. .. .... ..117
Filtering/smoothing
techniques.. .. .. .. ... . .. .. .. ... . ..117
miscellaneous.. . .. .... .. .. ... . .... .117
monitored values... . .. ... . .. .... ..117
operating conditions . .. .. .... .. .. .117
oxygen inlet . .. .. .. ... . .... .. .. .. ..117
power supply . . .. .. ... . .... .. .. .. ..117
settings .. .. .. .. .... .. .. ... . .. .. .. ..117
sound level . . .. ... . .... .. .. .. ... . ..117
SpO2
usage. ... . .. .. .. ... . ... . .. .. .. ... . ...69