Brother TC-32B - default chapter; Table of Contents

TC-32B Contents
2004/01/19 1 eTCOMNCPRC.doc
Chapter 1 Program Composition-------------------------------- 1-1
1.1 Types and composition of program ------------------------------------1-2
1.2 Composition of block -------------------------------------------------------1-2
1.3 Composition of word --------------------------------------------------------1-3
1.4 Numerical values ----------------------------------------------------------1-3
1.5 Sequence number ---------------------------------------------------------------1-4
1.6 Optional block skip -------------------------------------------------------------1-4
1.7 Control out/in function---------------------------------------------------------1-4
Chapter 2 Coordinate Command -------------------------------- 2-1
2.1 Coordinate system and coordinate value -------------------------------2-2
2.2 Machine zero point and machine coordinate system ---------------2-3
2.3 Working coordinate system--------------------------------------------------2-3
Chapter 3 Preparation Function --------------------------------- 3-1
3.1 Outline of G code ----------------------------------------------------------------3-2
3.2 Positioning (G00) ------------------------------------------------------------3-9
3.3 Linear interpolation (G01) ----------------------------------------------------3-10
3.3.1 Chamfering to desired angle and cornering C ---------------------------------------------- 3-11
3.4 Circular/helical interpolation (G02, G03) --------------------------------3-14
3.4.1 Circular interpolation --------------------------------------------------------------------------- 3-14
3.4.1.1 Circular interpolation ---------------------------------------------------------------------- 3-14
3.4.1.2 XZ Circular interpolation ----------------------------------------------------------------- 3-15
3.4.1.3 YZ Circular interpolation ----------------------------------------------------------------- 3-16
3.4.2 Helical interpolation----------------------------------------------------------------------------- 3-20
3.4.3 Spiral interpolation (G02, G03) --------------------------------------------------------------- 3-21
3.4.4 Conical interpolation (G02, G03) ------------------------------------------------------------- 3-23
3.4.5 Cutter compensation procedure for spiral interpolation and conical interpolation
(G02, G03) ---------------------------------------------------------------------------------------- 3-26
3.5 Circle Cutting (G12, G13) -----------------------------------------------------3-27
3.6 Plane Selection (G17, G18, G19) -------------------------------------------3-28
3.7 Dwell (G04)-------------------------------------------------------------------------3-29
3.8 Exact stop check (G09, G61, G64) -----------------------------------------3-29
3.9 Programmable data input (G10) --------------------------------------------3-31
3.10 Soft limit ----------------------------------------------------------------------------3-34
3.10.1 Stroke -------------------------------------------------------------------------------------------- 3-34
3.10.2 Stroke limit -------------------------------------------------------------------------------------- 3-34
3.10.3 Programmable stroke limit (G22) ----------------------------------------------------------- 3-35
3.11 Return to the reference point (G28) ---------------------------------------3-36
3.12 Return from the reference point(G29) ------------------------------------3-37
3.13 Return to the 2nd/3rd/4th reference point (G30)----------------------3-37
3.14 Selection of machine coordinate system (G53)-----------------------3-37
3.15 Selection of working coordinate system (G54~G59)----------------3-38
3.16 Additional working coordinate system selection (G54.1) ---------3-38
3.17 Scaling (G50, G51) --------------------------------------------------------------3-39
3.18 Programmable Mirror Image (G50.1, G51.1)----------------------------3-43
3.19 Rotational transformation function (G68,G69) ------------------------3-46
3.20 Coordinate rotation using measured results(G168)-----------------3-48
3.21 Absolute command and incremental command (G90, G91)------3-48
3.22 Change of workpiece coordinate system(G92) -----------------------3-50
3.23 Skip function (G31,G131,G132)---------------------------------------------3-52
3.24 Continuous skip function (G31) --------------------------------------------3-53
3.25 Change of tap twisting direction(G133,G134) -------------------------3-53
3.26 High speed peck drilling cycle (G173)) ----------------------------------3-54