CG Emotron VFX Series User Manual

44 Installation CG Drives & Automation, 01-5326-01r5
* With cable lug for M6 screw.
** Valid when brake chopper electronics are built in.
*** Use 90
°C Mains and motor cables if surrounding temperature is higher than 35 °C otherwise 75 °C cables.
48-205-20
F2
4 - 500 kcmil
275 (for
AWG 4 - 2)
375 (for AWG
1 -300 kcmil)
500 (for AWG
350 -500
kcmil)
6 - 300 kcmil
275 (for
AWG 6 - 2)
375 (for AWG
1 -300Kcmil)
4 - 500 kcmil
6 - 2/0**
275 (for
AWG 4 -
2)
375 (for
AWG 1 -
300 kcmil)
500 (for
AWG 350
-500
kcmil)
88**
Copper
(Cu)
75°C
48-244-20
48-293-20
48-210-54
F
48-228-54
48-250-54
48-295-54 ***
48-365-20 FA2
M10 connection 416 M8 connection 212
M8
connection
212
Copper
(Cu)
75°C
48-365-54 FA
48-300
G
(2x) 4 - 500 kcmil
275 (for
AWG 4 - 2)
375 (for
AWG 1 - 300
kcmil)
500 (for AWG
350 -500
kcmil)
(2x) 4 - 500 kcmil
275 (for
AWG 4 - 2)
375 (for
AWG 1 -300
kcmil)
500 (for AWG
350 -500
kcmil)
PE/Earth via mounting
screws/mounting frame.
In order to secure proper
earthing, always use all
mounting screws and
tighten them thoroughly.
Copper
(Cu)
75°C
48-375
48-430
H
48-500
48-600
I (3x) 4 - 500 kcmil (3x) 4 - 500 kcmil
48-650
48-720,
750
48-860
J (4x) 4 - 500 kcmil (4x) 4 -500 kcmil48-900
48-1k0
48-1k15
KA (5x) 4 - 500 kcmil (5x) 4 - 500 kcmil48-1K2
48-1k25
48-1k35
K (6x) 4 - 500 kcmil (6x) 4 - 500 kcmil
48-1k5
48-1k75 L (7x) 4 - 500 kcmil (7x) 4 - 500 kcmil
48-2k0 M (8x) 4 - 500 kcmil (8x) 4 - 500 kcmil
48-2k25 N (9x) 4 - 500 kcmil (9x) 4 - 500 kcmil
48-2k5 O
(10x) 4 - 500
kcmil
(10x)4-500 kcmil
Table 20 Cable connector range and tightening torque for Emotron VFX48 and VFX52, according to NEMA ratings
Model VFX
Frame
size
Cable cross section connector range
Cable
type
Mains and motor Brake PE
Cable range
AWG
Tightening
torque
Lb-In
Cable range
AWG
Tightening
torque
Lb-In
Cable range
AWG
Tightening
torque
Lb-In

CG Emotron VFX Series Specifications

General

Brand	CG
Model	Emotron VFX Series
Category	Controller
Language	English