D-Link DGS-3120-48PC - Chapter 79 TFTP Client Command List

xStack
®
DGS-3120 Series Managed Switch CLI Reference Guide
710
Chapter 79 TFTP Client Command List
download [firmware_fromTFTP [<ipaddr> | <ipv6addr>] src_file <path_filename 64> {[unit
<unit_id> | all]} {dest_file <pathname>} | cfg_fromTFTP [<ipaddr> | <ipv6addr>] src_file
<path_filename 64> {[unit <unit_id> | all]} {dest_file <pathname>}]
upload [cfg_toTFTP [<ipaddr> | <ipv6addr>] dest_file <path_filename 64> {unit <unit_id>} {src_file
<pathname>} {[include | exclude | begin] <filter_string 80> {<filter_string 80> {<filter_string
80>}} {[include | exclude | begin] <filter_string 80> {<filter_string 80> {<filter_string 80>}}
{[include | exclude | begin ] <filter_string 80> {<filter_string 80> {<filter_string 80>}}}}} |
log_toTFTP [<ipaddr> | <ipv6addr>] dest_file <path_filename 64> | attack_log_toTFTP
[<ipaddr> | <ipv6addr>] dest_file <path_filename 64> {unit <unit_id>} | firmware_toTFTP
[<ipaddr> | <ipv6addr>] dest_file <path_filename 64> {unit <unit_id>} {src_file <pathname>}]
79-1 download
Description
This command is used to download the firmware image and configuration from TFTP server.
Format
download [firmware_fromTFTP [<ipaddr> | <ipv6addr>] src_file <path_filename 64> {[unit
<unit_id> | all]} {dest_file <pathname>} | cfg_fromTFTP [<ipaddr> | <ipv6addr>] src_file
<path_filename 64> {[unit <unit_id> | all]} {dest_file <pathname>}]
Parameters
firmware_fromTFTP – Specify to download firmware from a TFTP server.
<ipaddr> - (Optional) The IP address of the TFTP server.
<ipv6addr> - (Optional) The IPv6 address of the TFTP server. (EI Mode Only)
src_file - (Optional) Used to identify the parameter “path_filename”.
<path_filename 64> - Enter the source file path name here. This name can be up to 64
characters long.
unit - (Optional) Specify which unit on the stacking system. If it is not specified, it refers to the
master unit.
<unit_id> - Enter the unit ID value here. This value must be between 1 and n.
all - When all is specified, the firmware image on all units will be updated.
dest_file - (Optional) Used to identify the parameter “path_filename”.
<pathname>
- Enter the destination file path name here.
cfg_fromTFTP – Specify to download a configuration file from a TFTP server.
<ipaddr> - (Optional) The IP address of the TFTP server.
<ipv6addr> - (Optional) The IPv6 address of the TFTP server. (EI Mode Only)
src_file - (Optional) Used to identify the parameter “path_filename”.
<path_filename 64> - The pathname specifies the pathname on the TFTP server. It can
be a relative pathname or an absolute pathname. This name can be up to 64 characters
long.
unit - (Optional) Specify which unit on the stacking system. If it is not specified, it refers to the
master unit.
<unit_id> - Enter the unit ID value here. This value must be between 1 and n.
all - When all is specified, the firmware image on all units will be updated.
dest_file - (Optional) Used to identify the parameter “path_filename”.
<pathname>- The pathname specifies an absolute pathname on the device file system. If
pathname is not specified, it refers to the boot_up configuration file.