To Next PageTo Next Page
Need help?Do you have a question about the Doremi ShowVault and is the answer not in the manual?
Defines the objective of this manual in guiding users through ShowVault setup and installation.
Outlines the document's structure by listing its sections and their content.
Specifies the software version and IMB Certainty revision this document applies to.
Provides instructions and rules for correctly inserting hard disk drives (HDDs) into the unit.
Details the safe procedure for powering down the ShowVault to prevent RAID failure.
Lists technical support contact details for USA, Europe, and Japan regions.
Describes the components and LEDs visible on the ShowVault's front panel.
Illustrates and describes the connectors and ports located on the ShowVault's rear panel.
Explains how to connect the server LCD screen using the provided VGA cable.
Details the PCI Express card slot and its purpose for connecting to the IMB.
Provides an overview of the SuperMicro motherboard connectors like USB, Ethernet, and Serial.
Guides users through the process of changing the ShowVault's IP address settings.
Covers setting up and managing projector connections within the Device Manager.
Details the management of supported automation devices like eCNA and JNior.
Explains the configuration steps for enabling Dolby, RealD, and Sensio 3D support.
Describes how to enable and set up closed caption support for devices.
Introduces the graphical user interface of the Macro Editor for automation setup.
Details the creation and editing of Macro Automation Cues within the editor.
Explains the process of creating and managing Trigger Cues linked to events.
Provides instructions on how to verify the current time zone setting.
Guides users through the steps to change the ShowVault's time zone configuration.
Allows users to add, edit, and delete user accounts with specific privileges.
Enables users to change the language interface of the ShowVault system.
Manages the ingestion and viewing of software licenses for the unit.
Facilitates the generation of Composition Playlists (CPLs) for live events.
Explains how to view the current software and firmware versions installed on the ShowVault.
Provides a step-by-step guide for updating the unit's software and firmware using a USB drive.
Instructions for logging into the Linux system and opening a terminal locally.
Guides on how to establish a secure shell (SSH) connection to the ShowVault remotely.
Details how to create and save system status reports for troubleshooting purposes.
Covers the procedures for sending and performing software and firmware upgrades.
Explains how to identify RAID failures and reinitialize RAID partitions.
Describes the process of uploading files to the ShowVault using an FTP server.
Provides steps to modify the login password for the Linux system.
Guides on adjusting the display resolution for external VGA or front panel LCD screens.
Details the necessary BIOS settings for proper system boot-up and operation.
Explains maintenance procedures for the server's front panel LCD screen, including calibration.
Defines the structure of the XML file used for macro and trigger cue data.
Presents the XML Schema that defines the structure of Macro Automation Cues and Trigger Cues.
Provides a legend for the notation used in diagrams depicting XML structures.
Details the structure and elements of the Netmap configuration XML file.
Provides an example of a typical Netmap configuration file.
Lists potential issues or limitations related to the Netmap configuration file.
Guides on configuring the Device Manager for Dolby 3D support with a license.
Provides steps to configure the Device Manager for RealD 3D support.
Explains how to set up the Device Manager for Subtitle Engine functionality.
Introduces the IMB Certainty board, specifically focusing on Revision E.
Lists the necessary hardware components required for ShowVault setup with Barco projectors.
Provides instructions for the physical installation of the IMB board into the projector.
Details the steps for connecting the ShowVault server to the Barco projector.
Outlines the procedure for marrying the IMB with Barco Series 2 projectors.
Instructions for installing the IMB board into an NEC Series 2 projector.
Details the steps for connecting the ShowVault server to the NEC projector.
Explains the process for marrying the IMB with NEC Series 2 projectors.
Instructions for installing the IMB board into a Christie Series 2 projector.
Details the steps for connecting the ShowVault server to the Christie projector.
Describes the procedure for marrying the IMB with Christie Series 2 projectors.
Provides pinout information for GPIO connectors on the IMB Certainty board.
Details the pinout configurations for Audio AES connections.
Lists the 2D formats currently supported by the IMB's HD-SDI input.
Provides definitions for common acronyms and technical terms used in the document.
Chronological record of changes, versions, and updates made to the document.
General| Model | ShowVault |
|---|---|
| Type | Digital Cinema Server |
| Management Interface | Web-based interface |
| Video Formats Supported | MPEG-2 |
| Audio Formats Supported | PCM, Dolby Digital |
| Network Connectivity | Gigabit Ethernet |
| Operating System | Linux |
| Audio Outputs | AES/EBU, Analog |
| RAID Configuration | RAID 5 |
| Redundancy | Redundant power supplies (optional) |
| Power Supply | Dual redundant power supplies |
