DURKOPP ADLER 1767 - Service Instructions Manual

DURKOPP ADLER 1767

128 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

1767

Service Instructions

Table of Contents

Default Chapter3
- Table of Contents3
1 About These Instructions7
- For Whom Are These Instructions Intended7
- Representation Conventions - Symbols and Characters7
- Other Documents9
- Liability9
2 Safety11
- Basic Safety Instructions11
- Signal Words and Symbols Used in Warnings12
3 Working Basis15
- Order of the Settings15
- Laying the Cables15
- Removing the Covers16
- Access to the Underside of the Machine16
- Removing and Placing the Arm Cover17
- Removing and Placing the Head Cover18
- Removing and Placing the Rear Cover19
- Removing and Placing the20
- Disassembling and Assembling the Tensioning Plate21
- Removing and Placing the Belt Cover22
- Opening and Closing the Throat Plate Slide23
- Disassembling and Assembling the Throat Plate24
- Disassembling and Assembling the Feed Dog25
- Flats on Shafts26
- Locking the Machine in Place26
- Setting the Handwheel into Position28
4 Positioning the Arm Shaft29
5 Positioning the Toothed Belt Wheels31
- Positioning the Toothed Belt Wheel on the Motor Shaft31
- Positioning the Upper Toothed Belt Wheel32
- Positioning the Lower Toothed Belt Wheel33
- Setting the Toothed Belt Tension34
6 Setting the Handwheel Scale35
7 Latching the Safety Snap-On Coupling37
8 Setting the Stitch Length Adjusting Wheel39
- Setting the Stitch Length Limit40
- Setting the Basic Eccentric Setting for Forward Stitch and Backward Stitch42
9 Feed Dog43
- Setting the Feed Dog Position43
- Moving the Feed Dog44
- Moving the Feed Dog Carrier45
- Setting the Feed Dog Movement46
- Setting the Feed Eccentric46
- Setting the Compensating Weight47
- Setting the Feed Stroke Eccentric48
- Setting the Feed Dog Height at Top Dead Center49
10 Aligning the Needle Bar Linkage50
- Aligning the Needle Bar Linkage Sideways50
- Aligning the Needle Bar Linkage in the Sewing Direction53
11 Position of the Hook and Needle54
- Setting the Hook Side Clearance54
- Setting the Loop Stroke Position56
- Setting the Needle Bar Height58
- Setting the Needle Guard60
12 Setting the Bobbin Case Lifter62
- Setting the Lifting Gap63
- Setting the Timing for Opening64
13 Sewing Feet65
- Setting the Eccentric for the Top Feed Stroke65
- Setting an Even Sewing Foot Stroke67
- Setting the Adjusting Frame68
- Setting the Sewing Foot Lifting Height69
14 Setting the Thread Tensioning Spring71
15 Winder72
- Setting the Winder72
- Setting the Winder Wheel75
- Setting the Hook Thread Guide76
16 Thread Cutter77
- Setting the Height of the Thread-Pulling Knife77
- Setting the Cutoff Curve78
- Setting the Cutting Pressure80
- Setting Point in Time for Cutting81
17 Short Thread Cutter83
- Setting the Locking Latch86
- Setting the Thread-Pulling Knife87
- Setting the Counter Blade88
- Setting the Cutoff Position90
18 Setting the Potentiometer91
19 Programming93
- Control Panel OP100093
- Display93
- Buttons94
- Using Button Groups97
- Thread Button Group Functions98
- Setting the Start Bartack98
- Setting the Multiple Start Bartack99
- Using the Multiple Start Bartack as the Darning Program99
- Setting the End Bartack100
- Setting the Multiple End Bartack101
- Activating the Thread Cutter101
- Activating the Thread Clamp101
- Setting the Needle Position after Sewing Stop102
- Activating Sewing Foot Lift after Thread Cutter102
- 10Activating Sewing Foot Lift after Sewing Stop102
- Activating the Soft Start103
- 12Reducing Speed103
- Programming Button Group Functions104
- Setting the Bobbin Piece Counter104
20 Maintenance107
- Cleaning108
- Areas Requiring Special Cleaning109
- Cleaning the Motor Fan Mesh110
- Lubricating111
- Checking the Oil Level112
- Lubricating the Gear113
- Servicing the Pneumatic System115
- Setting the Operating Pressure115
- Draining the Water Condensation116
- Cleaning the Filter Element117
- Parts List118
21 Decommissioning119
22 Disposal121
23 Troubleshooting123
- Customer Service123
- Errors in Sewing Process123
24 Technical Data125

Other manuals for DURKOPP ADLER 1767

Operating Instructions112 pages

Related product manuals

Preview: DURKOPP ADLER 171

DURKOPP ADLER 171

Preview: DURKOPP ADLER 650-10

DURKOPP ADLER 650-10

Preview: DURKOPP ADLER 100-68-1

DURKOPP ADLER 100-68-1

Preview: DURKOPP ADLER 745-35-10 S

DURKOPP ADLER 745-35-10 S

DURKOPP ADLER 745-35-10 A

Preview: DAC BASIC - V 12-2010

DAC BASIC - V 12-2010

Preview: DURKOPP ADLER 767

DURKOPP ADLER 767

Preview: DURKOPP ADLER 580

DURKOPP ADLER 580

Preview: DURKOPP ADLER 867

DURKOPP ADLER 867

Preview: DURKOPP ADLER 888

DURKOPP ADLER 888

DURKOPP ADLER 238

Preview: DURKOPP ADLER M-TYPE 867

DURKOPP ADLER M-TYPE 867