What to do if DURKOPP ADLER Sewing Machine shows sewing motor current error?
If your DURKOPP ADLER Sewing Machine shows a sewing motor current error, it might be due to a blocked sewing motor, a disconnected or defective encoder cable, or a defective encoder. First, remove any blockage that may be obstructing the sewing motor. Then, check the encoder cable and replace it if necessary. If the problem persists, consider replacing the sewing motor.
How to fix DURKOPP ADLER 650-10 Sewing Machine sewing motor error with encoder plug?
If your DURKOPP ADLER Sewing Machine displays a sewing motor error related to the encoder plug, it could be that the encoder plug (Sub-D, 9-pin) is not connected or is defective, or the encoder itself is defective. Check the connection of the encoder cable and replace it if necessary.
What to do if DURKOPP ADLER 650-10 displays sewing motor plug error?
If you're getting a sewing motor error on your DURKOPP ADLER Sewing Machine because the sewing motor plug is not connected or is defective, check the connection of the sewing motor cable. Also, test the sewing motor phases (R = 2.8?, high impedance to PE). If needed, replace the encoder, the sewing motor, or the control.
Why DURKOPP ADLER 650-10 shows sewing motor insulation error?
If your DURKOPP ADLER Sewing Machine is showing a sewing motor insulation error, check the motor phase and PE for a low-impedance connection. If necessary, replace the encoder or the sewing motor.
How to correct incorrect rotation direction of DURKOPP ADLER 650-10 Sewing Machine motor?
If your DURKOPP ADLER Sewing Machine's sewing motor is rotating in the wrong direction, replace the encoder. Also, check the plug assignment and change it if necessary. Inspect the wiring in the machine distributor and correct it if needed. Finally, test the motor phases and ensure they have the correct value.
What to do if DURKOPP ADLER Sewing Machine exceeds maximum speed?
If your DURKOPP ADLER Sewing Machine displays a sewing motor error indicating that the maximum speed has been exceeded, the sewing motor cable is defective, or the sewing motor itself is defective, try switching the machine off and on again. If that doesn't work, replace the encoder. You can also perform a reset. If the issue persists, consider replacing the sewing motor.
How to fix DURKOPP ADLER 650-10 synchronization error?
If your DURKOPP ADLER Sewing Machine shows a sewing motor synchronization error because the external synchronizer plug (Sub-D, 9-pin) is not connected, connect the plug of the external synchronizer to the controller, ensuring you use the correct connection (Sync). If the issue continues, replace the reference switch or synchronizer. Note that this is only required for machines with transmission.
What causes error in the reference run of DURKOPP ADLER 650-10?
To resolve an error during the reference run of your DURKOPP ADLER Sewing Machine, replace the encoder. Also, make sure to eliminate any stiff movement in the machine.
General| Brand | DURKOPP ADLER |
|---|---|
| Model | 650-10 |
| Category | Sewing Machine |
| Language | English |
Identifies the target audience for the manual.
Explains the meaning of symbols and formatting used in the manual.
Lists related or referenced documents for further information.
Outlines Dürkopp Adler's responsibility and limitations regarding machine use.
Provides fundamental safety guidelines for operating the machine.
Explains the meaning of warning signals and symbols to ensure user safety.
Identifies and labels the main parts of the sewing machine with a diagram.
States compliance with European health, safety, and environmental regulations.
Defines the intended application and limitations of the 650-10 machine.
Steps to ready the machine before starting sewing.
Instructions for powering the machine on and off using the main switch.
Procedure for safely replacing the sewing needle.
Guide for properly threading the needle with thread.
Steps for winding the bobbin thread onto the bobbin.
Procedure for safely changing the bobbin.
Importance and adjustment of thread tension for seam quality.
How to adjust needle thread tension for optimal stitch quality.
How to adjust hook thread tension for optimal stitch quality.
Adjusting the needle thread regulator for correct stitch formation.
How to raise and lower the sewing feet using the pedal.
Function and operation of the knee lever for program control.
Step-by-step guide for the sewing process, including starting and stopping.
Introduction to using the OP3000 control panel for machine settings.
Overview of the different modes available on the controller.
Details on operating the machine in manual mode.
Accessing frequently used functions via softkeys on the control panel.
Navigating menus for various machine adjustments and configurations.
How to perform sewing operations in manual mode via software.
Details on operating the machine in automatic mode.
Executing sewing programs in automatic mode.
Procedure for aborting an active sewing program.
Details on operating the machine in easy mode for program creation.
Method for creating sewing programs using the keyboard interface.
Method for creating sewing programs by manual sewing.
Details on operating the machine in edit mode for program management.
Modifying existing sewing programs via the software.
Steps to create a new sewing program via the software.
Duplicating an existing sewing program.
Removing a sewing program from memory.
Creating a mirrored version of a sewing program.
How to view the current software version of the control panel.
Instructions for updating the machine's software.
Introduction to the OP7000 control panel and its functions.
Guide to inputting numerical data via the OP7000 panel.
Guide to inputting text (e.g., program names) via the OP7000 panel.
Overview of the different modes available on the OP7000 controller.
Details on operating the machine in manual mode using OP7000.
Lists adjustable parameters in OP7000 manual mode.
How to perform sewing operations in OP7000 manual mode.
Details on operating the machine in automatic mode using OP7000.
Lists adjustable parameters in OP7000 automatic mode.
How to perform sewing operations in OP7000 automatic mode.
Details on operating the machine in EDIT mode using OP7000.
Lists adjustable parameters in OP7000 EDIT mode.
Steps to create new sewing programs via OP7000.
Duplicating programs in OP7000 EDIT mode.
Removing programs in OP7000 EDIT mode.
Adjusting stitch length in OP7000 EDIT mode.
How to view software version on OP7000.
Information on the SERVICE mode in OP7000.
Instructions for updating software via OP7000.
Procedures for cleaning the sewing machine to ensure optimal operation.
Guide for lubricating machine parts to ensure smooth operation.
Information on how to obtain machine parts and accessories.
Verifies all included parts are present before installation.
Steps to remove shipping restraints from the machine.
Instructions for assembling the machine stand.
Steps to prepare the tabletop before mounting.
How to connect the tabletop and pedals to the stand.
Final steps for assembling the tabletop components.
Adjusting the machine's working height for ergonomic comfort.
Procedure for installing the machine head onto the stand.
Critical steps for connecting the machine's electrical components.
How to connect cables to the machine head.
Connecting pedal input devices to the controller.
Procedure for ensuring electrical safety through bonding.
How to connect the knee lever cable.
Steps to connect the control panel to the machine.
Performing a final check after setup to ensure proper function.
Contact information for technical support and repairs.
Explains software error codes and their solutions.
Lists common sewing problems and their remedies.
To Next Page
