Ecotech WinAQMS

To Next Page

To Previous Page

Appendix WinAQMS Mini DAS User manual 1.0

Add 3 channels with settings shown in table 9 to the new analyser and then hit OK.

Table 9 Settings for the NO, NOx, and NO

channels.

9841 NO Channel

9841 NOx Channel

9841 NO

Channel

System Channel #

Label

NOx

NO2

Multiplier

Offset

Units

ppm

Decimal Places

High Alarm

0.1

0.4

0.1

Low Alarm

Alarm Number

Valid Data High

Valid Data Low

Channel Type

NOX

NO2

Process

Average

Description

Nitrogen Monoxide

Nitrous Oxide

Nitrogen Dioxide

Log Report 1

Set (ticked)

Log Report 2

Set (ticked)

Log Report 3

Set (ticked)

Log Report 4

Set (ticked)

Out of Service

Unset (not ticked)

Serial Port Output

Set (ticked)

Alternate File Output

Set (ticked)

Main Page

Table of Contents6
Introduction11
Users and Passwords11
Figure 1 Winaqms Mini das Logger11
Software Protection Device12
About this Manual12
Figure 2: Winaqms Mini das USB Dongle12
Winaqms Mini das Architecture13
Winaqms Mini das Agent13
Figure 3 the Winaqms Mini das Architecture13
Figure 4 Winaqms Mini das Agent Interface14
Installation and Setup15
Setting up Users and Permissions in Windows 2000/Xp15
Adding Local Users to the Winaqms Mini das15
Giving the Winaqms Mini das User Permission to Log on as a Service15
Figure 5 the Control Panel15
Setting Windows Xp to Accept Dialup Connections16
Figure 6 Adding a Modem Dialup Support to Windows 200016
Figure 7 Selecting the Incoming Connection Modem17
Figure 8 Selecting the Incoming Connection Users17
Figure 9 Setting the Incoming Connection Properties18
Figure 10 Setting the Incoming Connection IP Addresses18
Connecting a Remote Client to a Winaqms Mini das19
Figure 11 Connecting to a Remote Winaqms Mini das19
General Information21
Figure 12 Menu Shortcuts21
Figure 13 Menu Buttons21
Figure 14 Minimise and Maximise Buttons21
Figure 15: Minimised Form21
Figure 16 Maximised Form22
Figure 17 Help Index23
Figure 18 about Winaqms Mini das23
Figure 19 Registered User Details23
Figure 20 User List Window24
Figure 21 Login Window24
Edit Menu27
System Parameters27
Figure 22 System Parameters27
Analyser Parameters28
Figure 23 Analyser Parameters28
Information29
Communication Settings31
Figure 24 Communication Settings in Analyser Parameters31
Channel Information33
Figure 25 Channel Information in Analyser Parameters33
Calibration Control36
Figure 26 Calibration Control in Analyser Parameters36
Digital Input and Output Settings37
Figure 27 Digital Input Settings in Analyser Parameters37
Calculated Channels38
Alculated Hannels38
Figure 28 Digital Output Settings in Analyser Parameters38
Figure 29 Calculated Channels38
Vector Averaged Channels40
Rolling Averages40
Figure 30 Vector Averaged Channels in Calculated Channels40
Report Settings41
Figure 31 Rolling Average Channels in Calculated Channels41
Figure 32 Report Settings42
Alarms43
Figure 33 Alarms43
Figure 34 Alarm Email Details44
Figure 35 Wincollect Alarm44
Logs45
Figure 36 Log Entry Window45
Display Schemes46
Figure 37 Logs Main Screen46
Figure 38 Saving Settings to a Display Scheme46
Remote Logger47
Figure 39 Adding a New Display Scheme47
Figure 40 Remote Logger Window47
Figure 41 RS232 Connection Settings48
Security49
Data Pusher49
Figure 42 TCP/IP Connection Settings49
Figure 43 Data Pusher Screen49
Data Server Settings51
Figure 44 Serial RS232 Tab51
Figure 45 Protocol Settings Tab51
Figure 46 Telnet Settings52
Figure 47 Modbus Settings52
Stack Sequencing53
Figure 48 Stack Sequencing Window53
View Menu55
Calibration Status55
Channel List55
Figure 49. Calibration Status Window55
Historical Data56
Figure 50 Channel List Screen56
Figure 51 Historical Data56
Historical Graph57
Figure 52 Historical Graph57
Figure 53 Historical Graph Settings with Plot Settings58
Figure 54 Historical Graph Settings with Axis Settings58
Instantaneous Data59
Instantaneous Graph59
Figure 55 Instantaneous Data59
Figure 56 Instantaneous Graph59
Instantaneous Wind Speed/Direction60
Figure 57 Instantaneous Graph Settings with Plot Settings60
Figure 58 Instantaneous Graph Settings with Axis Settings60
Figure 60 Wind Speed and Direction Settings61
Sizeable Font Data Value63
Figure 61 Sizeable Font Data Value Window63
Figure 62 Font Size Settings Window63
Manual Menu65
Start Calibration65
Figure 63 Start Manual Calibrations65
Communicate with Serial Port66
Figure 64 Communicate with Serial Port66
Communicate with Analyser67
Figure 65 Communicate with Analyser67
Figure 66 Ecotech Gascal 1000 Point Settings68
Figure 67 Ecotech Gascal 1000 Gas Settings68
Figure 68 Ecotech Gascal 1000 Alarm Settings69
Figure 69 Ecotech Gascal 1000 Factory Settings69
Digital Outputs70
Figure 70 Disabling Scheduled Calibrations70
Figure 71 Manually Setting Digital Outputs70
Channel State71
Restart Server71
Suspend/Resume Logging71
Figure 72 Channel State71
Stop Server72
Figure 73 Stop Server Confirmation Box72
Appendix A - Configuring Winaqms Mini das Example73
Figure 74 Winaqms Mini das Loading73
Figure 59 Wind Speed and Direction76
Appendix B - Compatible Modems82
Appendix C - How to Set up the Analysers83
Appendix D - Usb Protocol Parameter List85
Appendix E - Ecotech Termination Panel Connections90
Appendix F - Setting up Drivers and Modems91
Appendix G - Serial Output Report Formats93
Appendix H - Winaqms Mini das Status Information95

Ecotech WinAQMS - Page 78

Table of Contents