37
In the scanner status area, either of the following messages is shown, if the product doesn’t have print function.
“Available.” “Busy. ” When outside is indicated, a link to a Panel Snapshot is indicated under the message.
Table 10-2 Scanner Status
One of the following messages is shown in the hardware status area.
Table 10-3 Hardware Status
This message is shown when the
scanner is ready to use.
This message is shown when the
scanner is busy.
"Paper jam. Remove the jammed paper in
the Automatic Document Feeder (ADF)"
This message is shown when the
scanner is in paper-jam condition.
"Incorrect size documents have been
placed in the Automatic Document Feeder
(ADF).
This message is shown when the
scanner is in ADF paper size error
condition.
"Double feed has occurred."
This message is shown when the
scanner is in double feed error
condition.
"The number of scans is close to the Life
Cycle of the rollers."
This message is shown when
consumable roller should be replaced.
-Only consumable roller support
printers.
"The number of scans exceeds the Life
Cycle of the rollers."
This message is shown when
consumable roller must be replaced.
-Only consumable roller support
printers.
"Unavailable. Check [Hardware Status]."
This message is shown when the
scanner has some error due to the
mechanical failure and is unable to use.
"An error has occurred. Please confirm the
indicator or message on the product."
This message is shown when the status
is other than those above.(This error
does not occur in the product.)
"Scanner is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only Scanner is out of order. An
error code is shown right behind the message. The string is
shown in red.
A link to a Panel Snapshot Page is indicated.
"Fax is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only Fax is out of order. An error
code is shown right behind the message. The string is shown in
red.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-1) is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only G3-1 is out of order. The
string is shown in red.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-1) : It can not be used with the current firmware.
Please update the firmware."
This message is shown when only G3-1 can not be used due to
version mismatch.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-2) is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only G3-2 is out of order. The
string is shown in red.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-2) : It can not be used with the current firmware.
Please update the firmware."
This message is shown when only G3-2 can not be used due to
version mismatch.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-3) is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only G3-3 is out of order. The
string is shown in red.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-3) : It can not be used with the current firmware.
Please update the firmware."
This message is shown when only G3-3 can not be used due to
version mismatch.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-4) is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only G3-4 is out of order. The
string is shown in red.
A link to a Panel Snapshot Page is indicated.
"Fax(G3-4) : It can not be used with the current firmware.
Please update the firmware."
This message is shown when only G3-4 can not be used due to
version mismatch.
A link to a Panel Snapshot Page is indicated.
"Wi-Fi is out of order. Contact Epson Support. "
"Panel Snapshot"
This message is shown when only Wi-Fi is out of order. An error
code is shown right behind the message. The string is shown in
red.
A link to a Panel Snapshot Page is displayed.
To Next Page
Loading...
Need help?
General