Extron electronics DTP CrossPoint 84 - Serial and IR Insertion Connections

DTP CrossPoint 84 Series Matrix Switchers • Installation 14
J
Audio Outputs 1 through 4 (see figure2 on page11)— Connect audio
LR
devices such as an audio amplifier or powered speakers, to these 5-pole,
3.5 mm captive screw connectors. These connectors output unamplified,
line level audio, whether it is tied from an analog input or de-embedded from an HDMI
input (see Analog audio input connectors on page19 to wire the connectors).
K
Amp output 1 (stereo audio model) — Connect unpowered,
1
L
R
4
CLASS 2 WIRING
8/
4-ohm or 8-ohm speakers to this 4-pole 5 mm captive screw
connector to play the amplified stereo audio from output 1.
L
Amp output 1 (mono audio model) — Connect unpowered speakers
1
CLASS 2 WIRING
to this 2-pole captive screw connector to play the amplified mono audio
from output 1.
ATTENTION:
• Ensure the rated input voltage of the speakers matches the rated
output voltage of the switcher.
•
Assur
ez-vous que la tension nominale d’entrée des enceintes soit
compatible avec la tension nominale de sortie du sélecteur
M
S/PDIF output 4 — Connect a compatible device to this RCA connector
S/PDIF
OUT
to receive digital audio signal stripped from the output 4 digital stream (see
S/PDIF output connector on page21 to wire this connector).
N
DMP Expansion Port and LED) —
EXP
LINK
Expansion port — Connect a CAT 6 cable between this port and the
Expansion port on an optional Extron DMP 128 ProDSP Digital Matrix
Processor. A shielded 1-foot cable is included with the DMP 128. Expansion
supports audio system scalability with expanded audio processing and signal routing
capabilities (see Expansion Port Operation Within the DSP on page124 for details
on using this functionality). No setup is required; just connect the two devices.
Link LED — Lights to indicate that the port is connected to a compatible device.
Serial and IR Insertion Connections
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
SIG LINK
OUT
1
3
4
4
XTP
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
HDBT
G
DTP
HDBT
2
1234
5
8
6
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
Figure 6. Serial and IR Insertion Connections
O
Over TP (Inputs 7 and 8) ports— If desired, connect serial RS-232
RS-232 IR
Tx Rx Tx RxG
signals, modulated IR signals, or both to these 3.5 mm, 5-pole captive
screw connectors to insert bidirectional RS-232 and IR communications
onto the associated inputs (see Serial and IR port connectors on page20
to wire the cables).
P
Over TP (Outputs 3 and 4) ports — If desired, connect serial RS-232
RS-232 IR
Tx Rx Tx RxG
signals, modulated IR signals, or both to these 3.5 mm, 5-pole captive
screw connectors to insert bidirectional RS-232 and IR communications
onto the associated outputs (see Serial and IR port connectors).
6
Amp OUTPUTS 1 (SA Model)
Amp OUTPUTS 1 (MA Model)
S/PDIF OUTPUTS 4
DMP Expansion Port and LED
Over TP (Inputs 7 and 8) ports
Over TP (Outputs 3 and 4) ports
Audio Outputs 1 through 4