A1400 AIR RDT 78 532119 04 - Rev. C
Translation of the original instructions
ENGLISH
16.4 UPDATE UPLOAD
The USB memory files are copied on the board.
The update files may be downloaded from the website:
www.faacgroup.com
The USB device must be formatted with FAT or FAT 32 file system. The
NTFS format is not recognised by the control board.
The required files, with names exactly defined in 21 must be
directly available on the USB memory (not inside folders, nor zipped).
Use a USB with maximum 500mA absorption.
1. When switched on the board is in Bootloader mode for a few
seconds which is viewed on the display with
bo
2. insert the USB memory device in the J17 connector
3. the USB device is detected and the display shows the letters
bo
4. press and release the button
F to scroll through available func-
tions (19)
5. to perform the displayed function, press simultaneously + – for
at least 3 s; update starts:
-- blinks on the display and the USB
LED blinks on the board. Upon completing the operation, the
display will show:
y = if successfully completed
no = in the event of errors (RED LED DL4 on the board on).
To display the error code, simultaneously press the 2 buttons + and –.
6. Remove the USB memory device.
16.5 DOWNLOAD
The board files are copied on the USB memory
The USB device must be formatted with FAT or FAT 32 file system. The
NTFS format is not recognised by the control board.
1. When switched on the board is in Bootloader mode for a few
seconds which is viewed on the display with
bo
2. insert the USB memory device in the J17 connector
3. The USB device is detected and the display shows the letters
bo
4. press and release the button
F to scroll through available func-
tions (20)
5. to execute the displayed function, simultaneously press + – for at
least 3 s until the display shows
Or or
Ad
6. release the buttons and use the + – buttons to select one of the
two file saving methods:
Or (overwrite) = the board file will be saved in USB memory
overwriting any file already present with the same name
Ad (add) = the board file is saved in USB memory in addition to
any file already present
(
*
)
7. Press F to save the file in the root of the USB memory
8. Upon completing the operation, the display will show:
y = if the operation has been completed successfully
no = in the event of errors (RED LED DL4 on the board on).
To display the error code, simultaneously press the 2 buttons + and –.
9. Remove the USB memory device.
19 Updating functions (UPLOAD) from USB
UP
Board firmware update E1400 RD (including AUX board FW).
required file: 1400RD.hex
UE
Firmware update SDK EVO and LKEVOincluding translations of messages
displayed by the device.
to update the SDK EVO two files are required on the USB device:
SDKEVO.hex
SDKEVO_L.bin
to update the LKEVO one file is required on the USB device:
LKEVO.hex
UC
E1400 RD board CONFIGURATION UPLOAD.
required file: 1400RD.prg
Ut
E1400 RD board TIMER CONFIGURATION UPLOAD.
required file: 1400RD.tmr
Should the board remain in the
bo status, an UPLOAD must be
performed
20 Download Functions on USB
dC
Board E1400 RD CONFIGURATION Download onto USB memory.
the file is copied: 1400RD.prg
(
*
)
dt
TIMER CONFIGURATION Download
This function lets you save the E1400 RD board TIMER configuration on USB
memory.
the file is copied: 1400RD.tmr
(
*
)
dL
LOG DATA Download
This function lets you save the E1400 RD board LOG data on USB memory.
the file is copied: 1400RD.log
(
*
)
(
*
)
If the USB memory root already has a file with the same name
and the
Ad mode was selected, an incremental number is added
to the new file name. E.g.: if a file 1400RD01.prg already exists the
file 1400RD02.prg is saved and so on.
21 Firmware and programming file names
1400RD.hex board firmware
1400RD.prg board programming
1400RD.tmr Timer programming
SDKEVO.hex firmware SDK EVO
SDKEVO_L.bin language update on SDK EVO
LKEVO.hex firmware LKEVO
To Next Page
Loading...
