Fuji Electric FRENIC MEGA G2 Series - Page 223

5.2 Function Code Tables
5-39
FUNCTION CODES
Chap 5
Function
code
Name
Control method and Data setting range
Change when running
Data copying
Factory
default
Related page
d125
Brake control signal (Brake-
apply timer) (REV)
0.0 to 5.000 s, 999
Y
Y
999
d150
PID control
(Dancer upper limit warning
position)
-100.00 to 100.00 %
Y
Y
100.00
d151
(Dancer lower limit warning
position)
-100.00 to 100.00 %
Y
Y
0.00
d152
(Line speed lower limit for
dancer PID output)
0.0 to 599.0 Hz
Y
Y
0.0
5-337
d153
Line speed control
(Line speed compensation
gain)
0.0 to 200.0 %
Y
Y
100.0
5-337
d154
(Selector switch)
0 to 1
Bit 0: Winding diameter compensation (0: No, 1: Yes)
N
Y
0
5-338
d158
Winding diameter
calculation
(Moving average count)
0 to 100
Y
Y
0
5-339
d159
(Dead zone)
0.000 to 10.000 %
Y
Y
0.001
d160
(Calculation gain)
0.00 to 1.00
Y
Y
0.10
5-339
d161
(Compensation gain)
0.000 to 10.000
Y
Y
1.000
5-339
d162
(Low-speed line speed ratio)
0.00 to 100.00 %
Y
Y
3.00
5-339
d163
(Minimum winding diameter)
1 to 65535 mm (3,300 to 4,900 ft)
Y
Y
100
5-340
d164
(Maximum winding
diameter)
1 to 65535 mm (3,300 to 4,900 ft)
Y
Y
1100
d165
(Initial winding diameter)
1 to 65535 mm (3,300 to 4,900 ft)
Y
Y
700
d166
(FM output gain)
0.0 to 100.0
Y
Y
20.0
5-341
d167
Line speed command
(Maximum value)
0.0: Disable
0.1 to 6553.5 m/min
N
Y
0.0
5-341
d168
(Acceleration time)
0.00 to 6000 s
Y
Y
*11
d169
(Deceleration time)
0.00 to 6000 s
Y
Y
*11
d170
After detected load
compensation (dedicated
monitor function code)
-327.68 to 327.67 %
-
N
-
5-343
d171
Load conversion gain
(hoisting)
0.00 to 200.00 %
Y
Y
100.00
d172
Load conversion offset
(hoisting)
-100.0 to 100.0 %
Y
Y
0.0
d173
Load conversion gain
(lowering)
-200.00 to 200.00 %
Y
Y
100.00
d174
Load conversion offset
(lowering)
-100.0 to 100.0 %
Y
Y
0.0
d175
Light load speed multiplying
factor (hoisting)
100.0 to 300.0 %, 999
Y
Y
100.0
d176
Light load speed multiplying
factor (lowering)
100.0 to 300.0 %, 999
Y
Y
100.0
d177
Medium load speed
multiplying factor (hoisting)
100.0 to 300.0 %,999
Y
Y
100.0
d178
Medium load speed
multiplying factor (lowering)
100.0 to 300.0 %, 999
Y
Y
100.0
d179
Speed multiplying factor
safety factor
1.0 to 4.0
Y
Y
1.0
d180
Load judgment delay time
(hoisting)
0.00 to 10.00 s
Y
Y
2.00
d181
Load judgment delay time
(lowering)
0.00 to 10.00 s
Y
Y
2.00
d182
Light load detection level
(hoisting)
5.0 to 100.0 %, 999
Y
Y
25.0
d183
Light load detection level
(lowering)
5.0 to 100.0 %, 999
Y
Y
25.0
d184
Heavy load detection level
(hoisting)
5.0 to 100.0 %, 999
Y
Y
25.0
d185
Heavy load detection level
(lowering)
5.0 to 100.0 %, 999
Y
Y
25.0
d186
Overload judgment delay
time
0.00 to 10.00 s
Y
Y
0.50
d187
Overload detection level
5.0 to 250.0 %, 999
Y
Y
999
d188
Overload detection monitor
-327.68 to 327.67 %
-
N
-
d189
Hoist function auxiliary
setting
0000 to 00FF (Display in hexadecimal)
Bit 0: Medium load speed multiplying factor selection
(0: Fixed multiplying factor, 1: Proportional to load)
Y
Y
0000