AquaTrans™ AT600 User’s Manual 23
Chapter 3. Wiring the AT600 Electronics
Chapter 3. Wiring the AT600 Electronics
3.1 Wiring Diagram
This section includes instructions for making all the necessary electrical connections to the AT600 flow
meter. Refer to Figure 23 below for the complete wiring diagram of the meter.
IMPORTANT: Except for the transducer connector, all electrical connectors are stored in their terminal blocks
during shipment and may be removed from the enclosure for more convenient wiring. Feed the
cables through the cable gland holes on the bottom of the enclosure, attach the wires to the
appropriate connectors and plug the connectors back into their terminal blocks.
After the AT600 is completely wired, proceed to “Initial Setup and Programming” on page 31 to configure the
meter for operation.
Figure 23: Wiring Diagram
Note: The HART and Modbus communication options must be selected when ordering the AT600.
ATTENTION EUROPEAN CUSTOMERS! To meet CE Mark requirements, all cables must be installed
as described in “Wiring Cable Specifications and Requirements” on page 177.
GROUNDING 4
A
GROUNDING 2
GROUNDING 1
GROUNDING 3
DETAIL A
Transducer Terminals
W/E >ĂďĞů ĞƐĐƌŝƉƟŽŶ
ϭ E ŽǁŶƐƚƌĞĂŵdƌĂŶƐĚƵĐĞƌ
Ϯ hW hƉƐƚƌĞĂŵdƌĂŶƐĚƵĐĞƌ
WŽǁĞƌdĞƌŵŝŶĂůƐ
W/E >ĂďĞů ĞƐĐƌŝƉƟŽŶ
ϭ >ϭ;нͿ >;нͿ>ŝǀĞWŽǁĞƌWŽƐŝƟǀĞ
Ϯ >ϮE;ͲͿ E;ͲͿEĞƵƚƌĂůEĞŐĂƟǀĞ
/ŶƉƵƚKƵƚƉƵƚdĞƌŵŝŶĂůƐ
>ĂďĞů ĞƐĐƌŝƉƟŽŶ
Ϭ ŶĂůŽŐKƵƚƉƵƚϰͲϮϬŵ,ZdWŽƐŝƟǀĞ
ϭ ŶĂůŽŐKƵƚƉƵƚϰͲϮϬŵ,ZdEĞŐĂƟǀĞ
Ϯ ^ĞƌǀŝĐĞDŽĚďƵƐWŽƌƚWŽƐŝƟǀĞ
ϯ ^ĞƌǀŝĐĞDŽĚďƵƐWŽƌƚEĞŐĂƟǀĞ
ϰ ^ĞƌǀŝĐĞDŽĚďƵƐWŽƌƚZĞƚƵƌŶ'ƌŽƵŶĚ
ϱ ƵƐƚŽŵĞƌDŽĚďƵƐWŽƌƚWŽƐŝƟǀĞ
ϲ ƵƐƚŽŵĞƌDŽĚďƵƐWŽƌƚEĞŐĂƟǀĞ
ϳ ƵƐƚŽŵĞƌDŽĚďƵƐWŽƌƚZĞƚƵƌŶ'ƌŽƵŶĚ
ϴ ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚWŽƐŝƟǀĞ
ϵ ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚEĞŐĂƟǀĞ
ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚWŽƐŝƟǀĞ
ŝŐŝƚĂůKƵƚƉƵƚWŽƌƚEĞŐĂƟǀĞ
E
'ĂƚĞ/ŶƉƵƚWŽƌƚWŽƐŝƟǀĞ
'ĂƚĞ/ŶƉƵƚWŽƌƚEĞŐĂƟǀĞ
& E
EŽƚĞŶĂůŽŐŽƵƚƉƵƚƐĂƌĞEĂŵƵƌEϰϯĐŽŵƉůŝĂŶƚ
To Next Page
Loading...
