Concord 4 Series Systems
31
Phones Menu
The PHONES menu lets you set up central station reporting for the system. The following
describes how to program the settings that appear under
CS PHONE 1-3.
Keyswitch Style (0015 - 0065)
Security-Partition 1-6 (Default = transition)
This feature allows users to select how they want the system to behave when
armed/disarmed by a keyswitch sensor. The choices are as follows:
Transition: If keyswitch style is set to transition and the keyswitch sensor is
tripped (opened) when the system is disarmed (level 1), the panel will auto-
matically arm to AWAY (level 3). If the sensor is tripped (opened) when the
system is armed to AWAY (level 3) or STAY (level 2), the panel will auto-
matically disarm.
State: If keyswitch style is set to state, when the keyswitch sensor is tripped
(opened) the panel arms to AWAY (level 3). If the sensor is restored (closed)
the panel disarms.
Opening, closing, and force arming reports (if turned on) are reported to the
central station for both keyswitch styles.
To assign a Keyswitch Style:
1. With the display showing KEYSWITCH
STYLE TRANSITION/STATE
(current set-
ting), press 1 for Transition or 2 for State.
The display flashes the entered setting.
2. Press # and the display shows the new set-
ting.
Duress Code (0016 - 0066)
Security-Partition 1-6 (Default = none)
The duress code is a unique 4-digit access code that allows users to operate
the system and, at the same time, instructs the panel to send a silent alarm
report to the central station.
Do not use a duress code unless it is absolutely necessary. Using duress codes
often results in false alarms due to code entry errors. If a duress code is abso-
lutely necessary, use it with an audio verification module (AVM) to reduce
false alarms and accidental dispatches.
Note
To use this feature, the Duress Option setting under the reporting—partition 1 (2)
menu must be turned on.
To program a Duress Code:
1. With the display showing DURESS CODE
****
, enter the desired 4-digit duress code.
The display flashes the entered setting.
2. Press # and the display shows the new
code.
To delete a Duress Code:
1. With the display showing DURESS CODE
nnnn
(current code), press D. The display
shows
DURESS CODE ****.
Phone Number (cs phone 1: 01000, cs phone 2: 01010,
cs phone 3: 01020)
Phones-CS 1-3 (Default = none)
This setting is used for programming the central station receiver phone number.
Phone numbers can be 1 to 24 digits long, including pauses or * and # characters.
To enter pauses, press C.
To enter *, press and hold 7 for about two seconds.
To enter #, press and hold 9 for about two seconds.
Note
The
PHONE NUMBER menus are not accessible if a Dealer Code is programmed and the
Installer Code is used to enter installer programming mode. To access these menus
when a Dealer Code is programmed, you must enter installer programming mode using
the Dealer Code.
Call-waiting services should be disabled to prevent interrupting panel communication to
the central monitoring station. To program a dialing prefix that disables call-waiting, see
the Call Wait Cancel setting under the menu
PHONE OPTIONS—GLOBAL.
For UL 1610 & 1635 installations, a phone number must be programmed.
To program a Central Station Phone
Number:
1. With the display showing PHONE
NUMBER _
(or current number), enter
the desired phone number. The dis-
play flashes the entered number.
2. Press # and the display shows the new
number.
To delete a Central Station Phone
Number:
With the display showing PHONE
NUMBER
(current number), press D.
The display shows PHONE NUMBER _.
WWW.DIYALARMFORUM.COM
To Next Page
Loading...
Need help?
General
