HP 1660 Series

To Next Page

To Previous Page

RUN Press the Run key, near the upper right corner of the front panel. You

will see the output of an 8-bit ripple counter like this:

Output of the 8-bit Ripple Counter

Next Please read the short introduction and chapter 1 before doing the exercises.

Introduction

iii

Get other manuals https://www.bkmanuals.com

Main Page

Table of Contents7
Using the Analyzer and Understanding the Measurement Process11
Using the Analyzer13
Understanding the Measurement Process14
Introduction to Timing Analysis19
Before You Begin21
Put the Analyzer into Timing Mode22
Change a Label Name23
Modify Channel Assignments24
Define a Term for the Timing Trigger25
Set up the Trigger Specification26
Trigger on the Term and Examine the Waveform27
Introduction to State Analysis29
Before You Begin31
Put the Analyzer into State Mode32
Set up the State Clock33
Change a Label Name34
Modify Channel Assignments35
Define a Term for the State Trigger36
Set up Level 1 of the State Trigger Specification37
Set up Level 2 of the State Trigger Specification38
Run the State Analyzer and View and Change the State Listing39
Create Symbols to Display State Data40
Create Additional Symbols41
Select and View Symbols in the State Listing42
Comparing State Traces before You Begin45
Check the Configuration46
Set up the State Trigger Specification47
Run the Analyzer and View the State Listing48
Copy the State Listing to the Compare Reference Listing49
Change the Jumper to Acquire a Different State Listing50
Run the Analyzer and Find the Errors51
Mixed Mode - Correlation of State and Timing Data53
Before You Begin55
Connect the Timing Analyzer56
Put the Analyzer into State and Timing Modes57
Change a Label Name and Modify Channel Assignments58
Turn on the TCOUNT Label in the Waveform Menu58
Clear the Timing Analyzer Trigger59
Set up the State Trigger Specification59
Enable Time Correlation between the Timing and State Analyzers60
Arm the Timing Analyzer with the State Analyzer61
View the Mixed-Mode Display with Time-Correlated Markers62
Advanced State Triggering63
Before You Begin65
Put the Analyzer into State Mode66
Define State Trigger Terms "A" through "D67
Define State Trigger Term "E" and Range168
Add State Trigger Sequence Levels69
Set up Level 1 of the State Trigger Specification70
Set up Level 2 of the State Trigger Specification71
Set up Level 3 of the State Trigger Specification72
Set up Level 4 of the State Trigger Specification and Define a Combination Trigger Term73
Check the Trigger Specification75
Run the State Analyzer and View the Data76
Using the Oscilloscope79
Before You Begin81
Connect the Channel 1 Oscilloscope Probe82
Get the Waveform on the Display83
Delete Channel 2 from the Display84
Zoom and Scroll through the Clock Waveform85
Measure the Clock Period Manually86
Measure the Clock Period with Auto Measure87
Read Voltage with the Markers88
Triggering the Oscilloscope with the Timing Analyzer89
Before You Begin91
Set the Jumpers92
Connect the Oscilloscope Probe93
Get the Waveform on the Display94
Change the Oscilloscope Trigger95
Turn on the Timing Analyzer96
Set up the Timing Format Menu97
Define the Timing Trigger Term "Edge 198
Set up the Timing Trigger Specification99
Arm the Oscilloscope with the Timing Analyzer100
Add Oscilloscope Waveform to the Timing Waveforms101
Capture the Glitch with the Timing Analyzer and Oscilloscope102
Align the Glitch Displayed by the Oscilloscope and Analyzer103
Using the Pattern Generator105
Before You Begin107
Connect the Pattern Generator108
Turn on the Timing Analyzer109
Change a Label Name110
Modify Channel Assignments111
Set up the Timing Analyzer Trigger Term112
Add a Pattern Generator Label to the Timing Waveform Display113
Set up the Pattern Generator Format Menu114
Program the Pattern Generator Output116
Add Program Lines117
Start the Pattern Generator and View the Walking Ones Pattern118
Stop the Pattern Generator119
Introduction to Inverse Assembly121
Load the Inverse Assembler and Sample Listing123
View the Address, Data, and Status Labels124
View the Assembly Listing125
Filter the Captured Data126
Setting the Jumpers and Loading the Configurations127
To Set the Jumpers129
To Load a Configuration File131
All about the Logic Analyzer Training Board133
Power Source134
Circuit Description134
Jumpers135
Schematic136

Table of Contents

Other manuals for HP 1660 Series

Related product manuals