HP A5120 EI Series Configuration Guide

164
[ProviderA] interface gigabitethernet 1/0/3
[ProviderA-GigabitEthernet1/0/3] port link-type trunk
[ProviderA-GigabitEthernet1/0/3] port trunk permit vlan 10 50
# Set the TPID value in the outer tag to 0x8200.
[ProviderA-GigabitEthernet1/0/3] quit
[ProviderA] qinq ethernet-type 8200
2. Configure Provider B.
 Configure GigabitEthernet 1/0/1
# Configure VLAN 50 as the PVID of GigabitEthernet 1/0/1.
<ProviderB> system-view
[ProviderB] interface gigabitethernet 1/0/1
[ProviderB-GigabitEthernet1/0/1] port access vlan 50
# Enable basic QinQ on GigabitEthernet 1/0/1.
[ProviderB-GigabitEthernet1/0/1] qinq enable
[ProviderB-GigabitEthernet1/0/1] quit
 Configure GigabitEthernet 1/0/2
# Configure GigabitEthernet 1/0/2 as a hybrid port and configure VLAN 10 as the PVID of the port.
[ProviderB] interface gigabitethernet 1/0/2
[ProviderB-GigabitEthernet1/0/2] port link-type hybrid
[ProviderB-GigabitEthernet1/0/2] port hybrid pvid vlan 10
[ProviderB-GigabitEthernet1/0/2] port hybrid vlan 10 untagged
# Enable basic QinQ on GigabitEthernet 1/0/2.
[ProviderB-GigabitEthernet1/0/2] qinq enable
[ProviderB-GigabitEthernet1/0/2] quit
 Configure GigabitEthernet 1/0/3
# Configure GigabitEthernet 1/0/3 as a trunk port to permit frames of VLAN 10 and 50 to pass through.
[ProviderB] interface gigabitethernet 1/0/3
[ProviderB-GigabitEthernet1/0/3] port link-type trunk
[ProviderB-GigabitEthernet1/0/3] port trunk permit vlan 10 50
# Set the TPID value in the outer tag to 0x8200.
[ProviderB-GigabitEthernet1/0/3] quit
[ProviderB] qinq ethernet-type 8200
3. Configure third-party switches.
Configure the third-party switches between Provider A and Provider B as follows: configure the port that
connects GigabitEthernet 1/0/3 of Provider A and the port that connects GigabitEthernet 1/0/3 of
Provider B to allow tagged frames of VLAN 10 and 50 to pass through.
Selective QinQ Configuration Example
Network requirements
As shown in Figure 53,
 Provider A and Provider B are edge devices on the service provider network and are connected
through trunk ports. They belong to SVLAN 1000 and SVLAN 2000 separately.

HP A5120 EI Series Specifications

General

Uplink Ports	4 x SFP
Stacking	No
Management	CLI, Web, SNMP
Routing Protocols	RIP, OSPF
Power Supply	AC
MAC Address Table Size	16K
Dimensions	440 x 430 x 44 mm
Operating Temperature	0°C to 45°C
Operating Humidity	10% to 90% non-condensing
Model	HP A5120-24G EI Switch (JG234A)
VLANs	4094