HP EVA P6000 User Manual

Set CHAP
Provides for the configuration of the challenge handshake authentication protocol (CHAP).
Admin sessionAuthority
set chapSyntax
Example:
MEZ50 <1>(admin) #> set chap
A list of attributes with formatting and current values will follow. Enter a
new value or simply press the ENTER key to accept the current value. If you
wish to terminate this process before reaching the end of the list press 'q' or
'Q' and the ENTER key to do so.
Index iSCSI Name
----- ----------
0 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.0
1 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.1
2 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.01.50001fe150070ce9
3 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.02.50001fe150070ce9
4 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.03.50001fe150070ce9
5 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.04.50001fe150070ce9
6 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.01.50001fe150070cec
7 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.02.50001fe150070cec
8 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.03.50001fe150070cec
9 iqn.1986-03.com.hp:fcgw.MEZ50.0834e00025.b1.04.50001fe150070cec
Please select a presented target from the list above ('q' to quit): 2
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current value. If
you wish to terminate this process before reaching the end of the list press
'q' or 'Q' and the ENTER key to do so.
CHAP (0=Enable, 1=Disable) [Disabled] 0
CHAP Secret (Max = 100 characters) [ ] ****
All attribute values for that have been changed will now be saved.
Set FC
Configures an FC port.
Admin sessionAuthority
[<PORT_NUM>]set fcSyntax
The number of the FC port to be configured.[<PORT_NUM>]Keywords
Example 1:
MEZ50 (admin) #> set fc
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current value.
If you wish to terminate this process before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both ports.
Configuring FC Port: 1
-------------------------
Port Status (0=Enable, 1=Disable) [Enabled ]
Link Rate (0=Auto, 1=1Gb, 2=2Gb, 4=4Gb, 8=8GB) [Auto ]
Frame Size (0=512B, 1=1024B, 2=2048B) [2048 ]
Execution Throttle (Min=16, Max=65535) [256 ]
All attribute values for Port 1 that have been changed will now be saved.
Configuring FC Port: 2
-------------------------
Port Status (0=Enable, 1=Disable) [Enabled ]
Commands 215

HP EVA P6000 Specifications

General

Model	HP EVA P6000
Number of Storage Controllers	2
Management Software	HP Command View EVA
Drive Types	SAS, SSD
RAID Levels	RAID 0, 1, 5, 6
Connectivity	8 Gb Fibre Channel, 10 Gb iSCSI, 1 Gb iSCSI
Form Factor	Rack-mounted
Storage Controller Type	Dual controllers