FLAP – (Flap System) ................................................................................................................................... A-28
FM0-FM2 (Flap System) ............................................................................................................................... A-29
Delay (Flap System) ...................................................................................................................................... A-30
ELEFLP M – Elevator-to-Flap Mixing .................................................................................................... A-31
AILRUD M – Aileron-to-Rudder Mixing ............................................................................................ A-32
AIL DIFF. – Aileron Differential .................................................................................................................. A-33
SRV. SPEED – Servo Speed
.......................................................................................................................... A-35
Snap Roll ......................................................................................................................................................... A-36
GYRO SYS. – Gyro System ......................................................................................................................... A-37
Gyro Connections (Gyro System) ............................................................................................................ A-37
Fixed Gyro Gain (Gyro System) ................................................................................................................ A-38
Stick Override Gyro Gain (Gyro System) ............................................................................................... A-39
PROG MIX – Programmable Mixers ........................................................................................................ A-40
Standard Programmable Mixer – Example: Down Elevator at Idle .................................................... A-41
Multi-Point Mixer – Example: Eliminate Pitch-Coupling ....................................................................... A-43
Trainer – Trainer System ............................................................................................................................. A-45
X9503 Used as Master (Iinstructor) – (Trainer System) ..................................................................... A-45
X9503 2.4 Used as Slave (Student) – (Trainer System)
........................................................................ A-46
Timer – Timer System
................................................................................................................................. A-47
Monitor ........................................................................................................................................................... A-48
Utility Functions ............................................................................................................................................ A-49
Copy – Copy the Currently Selected Model to Another Model Memory ...................................... A-49
Transfer – Transfer the Model to Another Transmitter or to DataSafe ............................................ A-51
Receive a Model into the X9503 2.4 – (Transfer function) ................................................................. A-51
Receive a Model into the X9503 2.4 – (Transfer function) ................................................................. A-52
Sub Trim Usage and Mechanical Advantage ............................................................................................. A-53
Sub Trim ....................................................................................................................................................... A-53
Mechanical Advantage .............................................................................................................................. A-53
Dual Rates and Exponential Curves ......................................................................................................... A-54
Setup Sheet (Aircraft) .................................................................................................................................. A-55
X9503 2.4 Helicopter – Heli Mode
........................................................................................................... H-1
Introduction
................................................................................................................................................. H-1
Heli Programming - Please Read ................................................................................................................. H-1
Heli - Getting Started – System Menu Basics ........................................................................................... H-1
Access the System Menu ............................................................................................................................... H-2
Model SEL- Model Selection ......................................................................................................................... H-2
Copy – Copying the Currently Selected Model to Another Model Memory ................................... H-3
Data Reset – Reset the Model ..................................................................................................................... H-5
Type Select – To Activate the Heli Mode ................................................................................................... H-6
MDL Name-Enter a Name for the Model ................................................................................................. H-6
Transfer – Transfer the Model to Another Transmitter or to DataSafe .............................................. H-7
Transfer a Model From the X9503 2.4 – (Transfer function) – To Send ............................................ H-7
Transfer a Model to the X9503 2.4 – (Transfer function) – To Receive ............................................. H-8
Trim Step ........................................................................................................................................................... H-9
Heli - System Menu - Advanced Functions
..............................................................................................H-10
Additional Flight Modes 3 and 4 ................................................................................................................H-10
RUD TRIM: COM – (Flight Mode Trim Options) ................................................................................... H-11
Switch Assignments ......................................................................................................................................H-11
Activate/Deactivate Switches .....................................................................................................................H-12
Governor Program Activation ...................................................................................................................H-12
SWASH TYP-Swashplate Type
.................................................................................................................... H-13
Accessing the Swashplate Type Function .................................................................................................H-13
Function Mode............................................................................................................................................... H-14
Heli – Function List
...................................................................................................................................... H-14
D/R & EXP – Dual Rate and Exponential ................................................................................................ H-14
Auto Dual Rate ..............................................................................................................................................H-15
REV.SW - Servo Reversing .........................................................................................................................H-15
Sub Trim ........................................................................................................................................................... H-16
TRVL ADJ. – Travel Adjust ............................................................................................................................H-17
Swash Mix- CCPM Swashplate Mixing .................................................................................................... H-18
Variations of CCPM Mixing .................................................................................................................... H-18
CCPM Servo Connection/Channel Numbers .................................................................................... H-18
Accessing the Swashplate Mixing Function ......................................................................................... H-19
CCPM Exponential (EXP) ........................................................................................................................... H-19
THRO HOLD- Throttle Hold ....................................................................................................................H-20
Accessing the Throttle Hold Function .................................................................................................H-20
Stick Auto/Auto Cut Setting .......................................................................................................................H-21
Hold Delay ......................................................................................................................................................H-21
THRO CURV – Throttle Curves ............................................................................................................... H-22
Accessing the Throttle Curve Function ............................................................................................... H-23
Throttle Trim Lever Function .....................................................................................................................H-24
Hovering Throttle Lever ..............................................................................................................................H-24
Throttle Curve Exponential .......................................................................................................................H-24
Accessing the Throttle Curve Exponential Function ........................................................................H-24
PIT. CURV/Pitch Curves Function ............................................................................................................. H-25
Accessing the Pitch Curve Function ..................................................................................................... H-25
Hovering Pitch Lever ....................................................................................................................................H-26
Example of Throttle Curve and Pitch Curve Settings ...................................................................... H-26
Accessing the Revolution Mixing Function ......................................................................................... H-27
Setting up Revolution Mixing..................................................................................................................H-27
REVO.MIX/Revo Mix Function: Non Heading Lock Gyros Only .......................................................H-27
GYRO SENS/Gyro Gain Function .............................................................................................................H-28
Accessing the Gyro Gain Function .......................................................................................................H-28
Gyro Remote Gain Connections: JR G370, G770 and Others
..................................................... H-29
Remote Gain Gyros ..................................................................................................................................... H-29
Mixing – Cyclic-to-Throttle Mixing ...........................................................................................................H-29
Rudder-to-Throttle Mixing ......................................................................................................................... H-30
Accessing the Cyclic-to-Throttle Function .........................................................................................H-31
To Next Page
Loading...
Need help?
General
