JR X9503 2.4 User Manual

Table of Contents Table of Contents
G-6
G-7
Aileron-to-Throttle and Elevator-to-Throttle Mixing ...........................................................................H-31
Setting the Desired Flight Modes for Cyclic-to-Throttle Mixing ................................................... H-31
Governor- Governor Function .................................................................................................................. H-32
Accessing the Governor Function ........................................................................................................H-32
PROG MIX 1-6 – Programmable Mixes 1 through 6 ............................................................................H-33
Swashplate Timing Mixes Example: Elevator-to-Aileron (Corrects Vertical Tracking).................... H-35
Swashplate Timing: Aileron-to-Elevator (Corrects Rolling Maneuvers) ............................................H-37
Standard Programmable Mixes – Example: Right Aileron with Positive Pitch ............................. H-39
Multi-Point Mixes – Example: FMOD to Gear Mixing (Retract and other Functions)..................H-41
Trainer – Programmable Trainer System.................................................................................................. H-44
X9503 2.4 Used as Master (Instructor) – (Trainer System)
........................................................... H-44
X9503 2.4 Used as Slave (Student) – (Trainer System)
................................................................... H-45
Timer – Timer System .................................................................................................................................H-46
Monitor – Servo Monitor ........................................................................................................................... H-47
Setup Sheet (Helicopter) .............................................................................................................................H-48
Sailplane – GLID Mode....................................................................................................................................S-1
System Mode GLID Features
.....................................................................................................................S-1
Function Mode GLID Features
..................................................................................................................S-1
System Mode ......................................................................................................................................................S-2
System Mode ......................................................................................................................................................S-2
To Enter System Mode: ................................................................................................................................S-2
Model Select .......................................................................................................................................................S-3
Copy – Copying the Currently Selected Model to Another Model Memory .....................................S-4
Model Name ......................................................................................................................................................S-6
Type Select ..........................................................................................................................................................S-6
Model Reset .......................................................................................................................................................S-7
Transfer – Transfer the Model to Another Transmitter or to DataSafe ................................................S-8
Transfer a model from the X9503 2.4 – (Transfer Function) .................................................................S-8
Transfer a model to the X9503 2.4 – (Transfer Function) ......................................................................S-9
Trim Step .......................................................................................................................................................... S-10
Device Select ................................................................................................................................................... S-11
Flight Modes
................................................................................................................................................ S-11
Activating and Assigning Flight Modes ....................................................................................................... S-12
Motor Function .............................................................................................................................................. S-13
Flap and AUX Functions ............................................................................................................................... S-14
Activating / Inhibiting Channels .............................................................................................................. S-14
Wing Type ........................................................................................................................................................ S-15
Function Mode
........................................................................................................................................... S-16
D/R & EXP – Dual Rate and Exponential ................................................................................................. S-18
REV.SW – Servo Reversing ......................................................................................................................... S-19
Sub Trim ............................................................................................................................................................ S-20
TRVL. ADJ - Travel Adjust ............................................................................................................................. S-21
Elevator-to-Flap Mix ...................................................................................................................................... S-21
Aileron-to-Flap Mix ....................................................................................................................................... S-22
Differential ....................................................................................................................................................... S-22
Camber Adjust
................................................................................................................................................ S-23
Camber Mix .................................................................................................................................................... S-24
Aileron-to-Rudder Mix ................................................................................................................................. S-25
Buttery Mix (Landing Flaps) ....................................................................................................................... S-26
Flap Rate........................................................................................................................................................... S-27
Motor Hold ..................................................................................................................................................... S-27
Programmable Curve Mix 1 (Programmed for Spoiler-to-Elevator Mix).......................................... S-28
PROG MIX - Programmable Mixers .......................................................................................................... S-29
Multi-Point Programmable Mixer ............................................................................................................... S-33
Trainer – Programmable Trainer System................................................................................................... S-36
X9503 2.4 Used as Master (Instructor) – (Trainer System)
............................................................ S-36
X9503 2.4 Used as Slave (Student) – (Trainer System)
.................................................................... S-37
Timer
................................................................................................................................................................ S-37
Monitor
............................................................................................................................................................ S-38
Programming a 6-Channel Sailplane by Engineering Manager John Adams
...................................... S-39
Channel Assignment .................................................................................................................................. S-41
Step #1 Servo Assignment .......................................................................................................................... S-41
Step #2 System Mode ................................................................................................................................... S-42
Step #3 Selecting a Model Memory ........................................................................................................... S-42
Step #4 Selecting Model Type...................................................................................................................... S-43
Step #5 Naming a Model .............................................................................................................................. S-43
Step #6 Turning Off the Spoiler Stick Trim ............................................................................................... S-44
Step #7 Establishing Flight Modes .............................................................................................................. S-44
Step #8 Wing and Tail Type Select .............................................................................................................. S-45
Step #9 Entering FUNC.LIST ...................................................................................................................... S-45
Step #10 Servo Reversing ............................................................................................................................ S-46
Step #11 Sub Trim .......................................................................................................................................... S-47
Step #12 Travel Adjust ................................................................................................................................... S-48
Step #13 Buttery (Landing Flaps) ............................................................................................................. S-48
Setting Up Flight Modes ........................................................................................................................... S-49
Launch Mode Setup ................................................................................................................................... S-49
Step #14 Spoiler to Elevator Curve Mix (Programmable Mix 1) ....................................................... S-49
Step #15 Launch Pre-sets ............................................................................................................................ S-50
Step #16 Dual Rate and Exponential ......................................................................................................... S-51
Step #17 Elevator-to-Flap Mix .................................................................................................................... S-51
Step #18 Aileron-to-Flap .............................................................................................................................. S-52
Step #19 Aileron Differential ....................................................................................................................... S-52
Flaperon Mix ............................................................................................................................................... S-53
Step #20 Flap Rate, Camber Mix and Camber Adjust ........................................................................... S-53
Step #21 Flap Rate, Camber Mix and Camber Adjust (continued) .................................................... S-54
Flaperon Mix ............................................................................................................................................... S-54
Flaperon Mix Delay .................................................................................................................................... S-54
Setting up Cruise Mode ............................................................................................................................ S-55
Step #22 Aileron-to-Rudder Mix ............................................................................................................. S-55
Step #23 Cruise Pre-sets ............................................................................................................................. S-56

JR X9503 2.4 Specifications

General

Brand	JR
Model	X9503 2.4
Category	Receiver
Language	English