JRC JLN-652 - Page 176

12-6
Standard Menu
（１１）
ALARM AND GRAPH SETTING
･C.SPD ALARM･L OFF kn :SELECT WITH / KEY
･S.SPD ALARM･L OFF kn :SELECT WITH / KEY
･BOTTOM DEPTH ALARM･S OFF 60 m :SET WITH KEY
･TIMER ALARM OFF 1:00 1:30 2:00 2:30 h
･TRIP ALARM OFF 1:00 2:00 3:00 4:00 NM
･TRIP/TIMER RESET CANCEL OPERATE
･TEMP ALARM･H OFF 10 11 12 13 14 15 16 17 ℃
･TEMP GRAPH CENTER 15 ℃ :SET WITH KEY
･TEMP GRAPH WIDTH OFF 1 2 4 8 ℃
･WIND SPEED ALARM･L OFF m/s :SELECT WITH / KEY
･MENU DISPLAY DISPLAY EXIT PREVIOUS
･HELP ≫ PUSH ENT KEY
（１２）
“UNDO” SETTING
･UNDO (RETURN TO FORMER MENU) CANCEL OPERATE
･MENU DISPLAY DISPLAY EXIT PREVIOUS
･HELP ≫ PUSH ENT KEY
（１３）
TIDAL CURRENT PICTURE SETTING
CURRENT GRAPH SETTING
･C.SPEED RANGE AUTO 1 2 4 6 8 10 kn
･CURRENT VECTORS DISP.ON/OFF ≫
･SHIP SPEED VECTORS DISP ON OFF
･GRAPH SIZE NORMAL LARGE
･WIND DIRECTION MARK DISP ON OFF
ECHO GRAPH SETTING
･ECHO GRAPH DEPTH RANGE 100 200 300 500 m
･ECHO GRAPH MODE ECHO SN
･SN. LEVEL HIGH 0 dB :SET WITH KEY
･SN. LEVEL LOW -12 dB :SET WITH KEY
･COLOR A B C D
･BACK COLOR STND BLK D.BLU GRY WHT
･MENU DISPLAY DISPLAY EXIT PREVIOUS
･HELP ≫ PUSH ENT KEY
（１４）
CURRENT VECTORS DISPLAY ON / OFF
･ABSOLUTE CURRENT VECTOR A DISP ON OFF
･ABSOLUTE CURRENT VECTOR B DISP ON OFF
･ABSOLUTE CURRENT VECTOR C DISP ON OFF
･ABSOLUTE CURRENT VECTOR D DISP ON OFF
･ABSOLUTE CURRENT VECTOR E DISP ON OFF
･RELATIVE CURRENT VECTOR A DISP ON OFF
･RELATIVE CURRENT VECTOR B DISP ON OFF
･RELATIVE CURRENT VECTOR C DISP ON OFF
･RELATIVE CURRENT VECTOR D DISP ON OFF
･RELATIVE CURRENT VECTOR E DISP ON OFF
･MENU DISPLAY DISPLAY EXIT PREVIOUS
･HELP ≫ PUSH ENT KEY
（１５）
CURRENT DEPTH SETTING :SETTING WITH A NUMERICAL KEY
･A LAYER 12 m TOP LOCK
･B LAYER 20 m
･C LAYER 30 m
･D LAYER 50 m
･E LAYER 100 m BOTTOM LOCK
･MENU DISPLAY DISPLAY EXIT PREVIOUS
･HELP ≫ PUSH ENT KEY
UNDO
Refer to 3.2.3 “Basic Operation of Menu”.
MENU / PICTURE SETTING / TIDAL CURRENT ≫
Refer to 4.2 “Current Display Setting”.
MENU / PICTURE SETTING / TIDAL CURRENT ≫
CURRENT VECTORS DISPLAY ON/OFF
≫
Refer to 4.2.1 “Current Circle Graph Setting”.
CURRENT DEPTH SETTING
Refer to 4.2.3 “Current Measurement Layer Depth
Setting”.
▲ ▼
▲ ▼
▲ ▼
MENU / MEASURE SETTING ≫ ALARM AND GRAPH
SETTING
≫
Refer to 4.1.8 “Alarm and Graph Setting”.