Keysight N9040B Option 508 User Manual

UXA RF BLOCK DIAGRAM - Option B5X
(Options 544, 550) (Highband Path - Input signals 3.6 GHz to 17.1 GHz)
UXA mm-Wave
BLOCK DIAGRAM
A15 FRONT END CONTROLLER
A20 YTO A14 LO SYNTH
A13A2 SWITCHED FILTER
A11 LOWBAND
SWITCH
SWITCH 3
(Option LNP)
SW4
SW5
3.6 GHz - 50 GHz
3 Hz - 3.6 GHz Path
+30 dB
High Band
Preamp
1st LO OUT
from A16J702
Reference Bd
W18
260 MHz - 400 MHz
120 MHz
LPF
3.8 - 8.73 GHz
5.675 GHz
FL2
J1
W8
50 MHz, -35.3 dBm
J900
AUX
IF OUT
(Rear Panel)
J901
J902
IF In
Ext
IF In
W16
1
IF OUT
322.5 MHz
-33 dBm
EXT IF OUT
W22
J903
J102
J301
J1300
to A2J100
Analog IF Out
322.5 MHz, -34 dBm
W25
W41
to A21J17
Wideband Analog IF Out
-34 dBm
W27
(2nd IF, -36 dBm)
N/C
Burst
Trigger
J1100
W5
W55
W7
W6
A
A
A
W11
W51 W66
J800
J802
J700
J801
J300 J302
1
4
2
3
W54
W52
J3
ATTENUATOR CONTROL
LOW BAND SWITCH BYPASS CONTROL
LOW BAND SWITCH CONTROL
PRESELECTOR BYPASS/B5X FILTER CONTROL
PRESELECTOR DRIVER CONTROL
LOG
DET
IQ
Modulator
BP F1
BP F2
YTO
Driver
VCO
+10 to
-10 mA
DAC
DAC
SWITCHED FILTER CONTROL
SWEEP
RAMP
IF OUT from A13A1J7
NOTE: Power levels based on these settings:
Mode: Spectrum Analyzer unless otherwise noted
RF Calibrator 4.8 GHz, -25 dBm
Center Frequency 4.8 GHz
Span 0 Hz
Input Attenuation 10 dB
Preamp OFF
Auto Align OFF after initial Auto Align
*Note: The 10 MHz IF path is default.
Set IF path by pressing Mode/Meas,
IQ Analyzer (Basic), Meas Setup, IF Path
Signal levels above 3 GHz include cable loss
of measuring system
FOOTNOTES
1
IF Path* IF Freq. Mode
10 MHz
25 MHz
40 MHz
140 MHz
255 MHz
510 MHz
750 MHz
877.148 MHz
IQ
IQ
322.5 MHz SA or IQ
322.5 MHz IQ
250 MHz IQ
300 MHz IQ
BIAS
TEE
MIXER BIAS, AMP BIAS,
PREAMP BIAS, E-ATTEN CONTROL,
SWITCH CONTROL, 1st LO POWER OPTIMIZATION,
YTF TUNE RAMP
W65
W33
W60
W64
W59
W63
W62
W61
W28
J2
J4
W20 W21
IF
Out
Aux LO In
J2
J1
J6
J5
W23
YTO Main and
FM coil current drive
ECAL In
3
IF IN
IF INIF OUT
5122.5 MHz
-34 dBm
5172.5 MHz
0 dBm
5172.5 MHz
+13 dBm
blockuxa_rf_hi_OPTB5X_550
255 MHz BPF
5.1 GHz
5172.5 MHz
+13 dBm
5172.5 MHz
+10 dBm
IM
Generator
J2
W29
EXT
MIXER
W17
W30
Delay
To
SW4, SW5
W32
7200 MHz
from FL1
J1
J2
J8 J35002
A9 INPUT
ATTENUATOR A
A10 INPUT
ATTENUATOR B
10 dB
2 dB
2 dB
6 dB
20 dB
-41 dBm
30 dB
Cal Signal
From A16 Reference
50 MHz, -25 dBm or
4.8 GHz, -28 dBm
W3
W2
W4
-30 dBm
J
RF
Input
A12 YTF
SWITCH 6
(Option MPB)
W69
W68
W67
Preselector
1
4
2
3
A13A1 FRONT END
0 - 24 dB
+20 dB
17 to 34.5 GHz
34.4 to 50 GHz
J7
J9
J8
J13
3.6 to 17.1 GHz
4 GHz
4.8 GHz
-53 dBm
(if Option MPB
and bypassed
-48 dBm)
Preamp
Electronic Attenuator
Mixer #1
Mixer #3
Mixer #4
Mixer #2
14 GHz
LPF
17 GHz
LPF
J3J5
J10
J11
J6
ALIGNMENT
THERMOMETER
LO
DISTRIBUTION
J4
J12
J2
X2
J1
5122.5 MHz
-33 dBm
2nd LO
4800 MHz
+10 dBm
4-07-2016

Keysight N9040B Option 508 Specifications

General

Brand	Keysight
Model	N9040B Option 508
Category	Measuring Instruments
Language	English