Labconco Logic+ A2 - Acceptance Criteria

To Next Page

To Previous Page

5. Observe the average concentration of aerosol downstream.

Acceptance Criteria

Aerosol penetration shall not exceed 0.01%.

Reinstall the exhaust housing front plate, unsecure temporary Inlet Relief Valve hold

open, reinstall the work surface pieces.

Main Page

Table of Contents4
1: Introduction11
Contacting Labconco11
About this Manual12
Theory of Operation12
Type A212
Type B213
Type C1 - a Mode13
Type C1 - B Mode14
2: Safety Precautions15
Typographical Conventions15
General Safety Precautions17
Safety Precautions for this Product19
3: Catalog Number Configurator21
4: Serial Tag22
Serial Tag Location22
Serial Tag Information23
Primary Serial Tag23
Secondary Serial Tag23
5: Factory Test Report24
Test Report Location24
Test Report Information25
6: Additional Product Information26
Data Plate Location26
Data Plate Information27
7: Exhaust System Connections28
Exhaust Connection Best Practices28
Air-Tight Damper30
Exhaust System Requirements31
Type A2 Models31
Cell Logic+ Type A2 Models32
Type B2 Models32
Type C1 Models33
8: Configuration34
Current Configuration34
Change Configuration36
9: Calibration40
Certifier Password40
Adjusting Blower Speed41
Adjusting the Internal Air Damper43
Setting the Filter Life Gauge45
Type A2 (8-Inch through 10-Inch Sash) and Type B245
Type A2 (12-Inch Sash) and Type C146
Airflow Sensor Calibration47
Type A2 and Type C147
Type B248
Zero Point Calibration50
Vacuum Start Switch Calibration (Type C1 Only)51
10: Certification53
Certifier Password53
Type A2 HEPA Filter Leak Test Preparation53
Theoretical Upstream Concentration54
Upstream Concentration Sampling54
Type A2 Supply HEPA Filter Leak Test56
Acceptance Criteria57
Type A2 Exhaust HEPA Filter Leak Test58
Acceptance Criteria59
Type B2 Supply HEPA Filter Leak Test Preparation60
Theoretical Upstream Concentration60
Upstream Concentration Sampling60
Type B2 Supply HEPA Filter Leak Test62
Acceptance Criteria63
Type B2 Exhaust HEPA Filter Leak Test Preparation64
Theoretical Upstream Concentration64
Type B2 Exhaust HEPA Filter Leak Test65
Acceptance Criteria65
Type C1 Supply HEPA Filter Leak Test Preparation66
Theoretical Upstream Concentration66
Upstream Concentration Sampling66
Type C1 Supply HEPA Filter Leak Test68
Acceptance Criteria69
Type C1 Exhaust HEPA Filter Leak Test Preparation70
Theoretical Upstream Concentration70
Type C1 Exhaust HEPA Filter Leak Test72
Acceptance Criteria73
Downflow Velocity74
Acceptance Criteria75
Inflow Velocity76
Primary Method76
Acceptance Criteria78
Secondary Method79
Acceptance Criteria83
Work Area Air Cleanliness Test (Optional)84
Acceptance Criteria84
Lighting Test (Optional)85
Acceptance Criteria85
Noise Test (Optional)86
Acceptance Criteria86
Vibration Test (Optional)86
UV Light Intensity Test (Optional)87
Acceptance Criteria87
Ground Fault Circuit Interrupter (GFCI) Test88
Acceptance Criteria88
11: Quickcharts89
Quickchart - Type A2 3-Ft & 4-Ft90
Quickchart - Type A2 5-Ft & 6-Ft91
Type A2 Footnotes92
Quickchart - Type B293
Type B2 Footnotes94
Quickchart - Type C195
Type C1 Footnotes96
12: Advanced Service Procedures97
Tools97
Required97
Optional97
Removal of External Dress Panels98
Dress Panel98
Side Panels99
Front Sash100
Sash Level Adjustment100
Sash Sensor Adjustment or Replacement101
HEPA Filter Replacement104
Type A2 (8, 9, 10-Inch Sash)104
Type A2 (12-Inch Sash)107
Type B2110
Type C1114
Blower/Motor Replacement117
Type A2 (8, 9, 10-Inch Sash) & B2117
Type A2 (12-Inch Sash) & C1 Supply Blower/Motor121
Type A2 (12-Inch Sash) & C1 Exhaust Blower/Motor124
Changing the LED Lamps129
LED Lamp Socket Cap Replacement131
Changing the Optional UV Lamp132
UV Lamp Socket Replacement133
Type B2 Prefilter Replacement134
Air-Tight Damper Adjustment135
Preparing the Biosafety Cabinet for Gaseous Sterilization136
Service Fixture Installation & Service Connection137
13: Electrical Components140
Electronics Module140
Electronic Module Components141
Resetting a Circuit Breaker142
Power Supply Board143
Display Board144
Speaker145
Blower Motor146
Wiring Diagrams148
100-115V148
208-240V149
14: Troubleshooting150
Blower and Lights Not Working150
Blower Only will Not Start151
Lights Only will Not Illuminate152
UV Light will Not Illuminate153
Airflow Alert Activating154
Filter Life Gauge Not at 100% When New155
Contamination in the Work Area156
15: Diagnostics157
Sash Sensors157
Keypad158
Airflow Sensor (Optional)159
Canopy (Optional)160
16: Bms Data Output Connection161
Connection Type161
Data Output Format162
Data Output Rate162
Data Output String Definition163
Data Output Software Requirements164
17: Ventus Canopy Connection Kit165
Kit Catalog Numbers166
Installation Procedure166
Exhaust Damper Installation Procedure168
Canopy Switch Wiring Connection168
Calibrate for Operation169
18: Airflow Sensor Kit171
Installation - Type A2 Without Ventus Canopy171
Installation - Type A2 with Ventus Canopy173
Connection to Electronics Module175
Configuration (New Install Only)176
Calibration178
19: Uv Lamp Kit181
Kit Catalog Numbers181
Installation181
Configuration183
20: IV Bar Kit185
Kit Catalog Numbers185
Installation185
21: Prefilter Kit187
Kit Catalog Numbers (Type A2 and B2 Only)187
Installation187
Attach Prefilter(S) to Towel Catch - G4 Paper188
Attach Prefilter(S) to Towel Catch - Aluminum Washable189
22: en Alarm/Relay Contact Kit190
Installation190
Example 1 - Blower Relay Contact (Single Phase AC)194
Example 2 - Blower Relay Contact (Three Phase AC)195
23: Parts List196
Type A2 Consumables196
Type B2 Consumables197
Type C1 Consumables198
Advanced Service Components199

Labconco Logic+ A2 - Acceptance Criteria

Table of Contents

Related product manuals