Maxcess D-MAXE - Page 131

160 pages

Save Page as PDF

To Next Page

To Previous Page

TROUBLESHOOTING 10 - 15

D-MAXE with OI-B/OI-Nwww.maxcessintl.com MI 2-296 1 D

Fehlersuche.fm

Operator interface fuse To access the operator interface fuse, remove the rear panel.

Replace the fuse and reinstall the rear panel.

F101 - Power fuse, 2.5A delay

Figure 10.2: Operator interface fuse location

Main Page

Table of Contents3
Introduction6
About These Operating Instructions6
Proper Use7
Options7
Improper Use7
Operating Principle8
Modules8
Operating Principle9
Safety Instructions10
Important Information10
Information about Safety Instructions10
Symbols11
Preventing Hazards11
Installation and Commissioning11
Operation12
Maintenance12
Installation13
Transport and Storage13
Scope of Delivery13
Mounting14
Installation Location of D-MAXE Controller14
Installation Location of D-MAX Operator Interface OI-B/OI-N16
Mechanical Fastening of D-MAX Operator Interface OI-B or OI-N17
Electrical Connection18
Emergency Stop18
Power Supply of D-MAXE Controller18
Power Supply of D-MAX Operator Interface OI-B or OI-N18
Connecting the Sensors/Actuators18
Connections on the D-MAXE 1 Controller20
Connections on the D-MAXE 2 Controller20
Connections on the D-MAXE 3 Controller21
Leds on the D-MAXE Controller22
Connections on the Operator Interface22
MAXNET Addresses23
Operation24
Precondition24
Note24
Safety Instructions24
User Interface25
LED Displays on the Operator Interface OI25
Keys and Their Functions26
Display - User Level27
Display - Menu Level30
Menu Structure31
Menu Identification31
User Level33
Selection of "Devices34
Automatic Operating Mode36
Servo-Center Operating Mode37
Manual Mode38
Selection of "Jobs39
Shift Guidepoint40
Menu Level41
Information on Operation in the Menu Level41
Numeric Entries41
Sequences41
Selection Lists41
Operator Interface Menus43
Notes43
Conventions43
Menu 1.A.1 Language44
Menus 1.A.2 Control Options45
Menu 1.A.2.1 BMP Orientation46
Menu 1.A.2.3 Connect on Start49
Menus 1.A.3 Display Settings50
Menus 1.A.5 Network (X252
Menus 1.A.6 Service53
Commissioning54
Before Commissioning54
Controller Menus57
Notes57
Conventions57
1Y.2 Remote Control58
1Y.3 Job Settings60
1Y.4 Servo-Center72
1Y.5 Hardware Ios75
General Information about These Menus76
General Information about These Menus86
1Y.6 Control Options99
Menu 1Y.6.1 Mode Enable99
Menu 1Y.6.2 Job Enable99
Menu 1Y.6.3 Jog Keys100
Menu 1Y.6.4 Remote Control100
Menu 1Y.6.5 Length Unit100
1Y.7 Configuration102
Menu 1Y.7.1 Names102
Menu 1Y.7.2 Serial Number102
Menu 1Y.7.3 FW Number102
Menu 1Y.7.4 SW Number102
1Y.8 Network111
Menu 1Y.8.1 TCP/IP111
Menu 1Y.8.2 MAXNET111
Menu 1Y.8.3 Fieldbus112
Menu 1Y.8.4 MAC-ID112
1Y.9 Service113
Menu 1Y.9.1 Measuring Points113
Menu 1Y.9.3 Errors/Warnings114
Maintenance115
Maintenance Work115
D-Maxe Decommissioning116
Decommissioning116
10 Troubleshooting117
Troubleshooting Procedure117
Display Possibilities117
Procedure117
Leds on the D-MAXE Controller118
D-MAX Operator Interface119
Leds on the D-MAXE Operator Interface120
Leds L1 and L2120
Leds X2121
Icons in the Display of the D-MAX Operator Interface122
Faulty Behavior and Setting Errors125
Faulty Behavior128
Fuse Replacement130
11 Technical Data132
General Information132
D-MAXE Controller132
D-MAX Operator Interface OI-B or OI-N133
Inputs and Outputs of the D-MAXE Controller134
Parallel Input Matrix137
Parallel Output Matrix137
Jobs138
Actuators139
Cable Lengths141
Standards141
Accessories (Optional)142
Input Devices142
Assembly Accessories142
Menu Structure D-Maxe Controller143
Legend143
Operator Interface Menu Structure153
Legend153
14 Glossary157
15 Service160

Maxcess D-MAXE - Page 131

Table of Contents

Related product manuals