Meggitt VM600 - Page 21

VM600 MPS hardware manual (standard version) MAMPS-HW/E xxi
Edition 17 - February 2018
7.11 Differential housing expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24
7.12 Broad-band pressure monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25
7.13 Quasi-static pressure monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26
7.14 Differential quasi-static pressure monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
7.15 Quasi-static temperature monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
7.16 Differential quasi-static temperature monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28
7.17 Dual mathematical function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29
7.18 Narrow-band fixed frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-31
Part II: Installing VM600 MPS hardware and using the system
8 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.2 Attribution of slots in the rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
8.3 Rack safety requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8.3.1 Adequate ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
8.3.2 Circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
8.3.3 Supply wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
8.3.4 Instructions for locating and mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
8.4 Installation procedure for cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
8.4.1 First-time installation of the MPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
8.4.2 Subsequent installation of cards ("hot-swapping” capability) . . . . . . . . . . 8-12
8.4.3 Setting the IP address of the CPUM card. . . . . . . . . . . . . . . . . . . . . . . . . 8-18
9 CONFIGURATION OF MPC4 / IOC4T CARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.1 Definition of screw terminals on the IOC4T card . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
9.2 Connecting vibration and pressure sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
9.2.1 General considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
9.2.2 Connection diagrams for hardware powered by IOC4T / MPC4 . . . . . . . 9-10
9.2.3 Connection diagrams for unpowered hardware . . . . . . . . . . . . . . . . . . . . 9-13
9.2.4 Connection diagrams for externally powered hardware . . . . . . . . . . . . . . 9-14
9.2.5 Connection diagram for frequency generator . . . . . . . . . . . . . . . . . . . . . . 9-19
9.3 Connecting speed sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20
9.3.1 General considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
9.3.2 Connection diagrams for hardware powered by IOC4T / MPC4 . . . . . . . 9-23
9.3.3 Connection diagrams for unpowered hardware . . . . . . . . . . . . . . . . . . . . 9-25
9.3.4 Connection diagrams for externally powered hardware . . . . . . . . . . . . . . 9-26
9.3.5 Connection diagram for frequency generator . . . . . . . . . . . . . . . . . . . . . . 9-29