Home
MIMAKI
Plotter
CG-AR Series
MIMAKI CG-AR Series User Manual
4
of 1
of 1 rating
184 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Chapter 8 Dealing with Problems
172
Message
Cause
Corrective action
Replace with PEN
•
Waiting for the creasing tool
to be replaced with the pen.
•
Replace with the pen, then press the
[REMOTE] key.
Replace with CUT
•
Waiting for the creasing tool
to be replaced with the cutter.
•
Replace with the cutter, then press the
[REMOTE] key.
171
173
Table of Contents
default chapter
2
Table of Contents
2
Introduction
6
Product Description
8
Symbols
9
To Ensure Safe Use
9
Usage Precautions
10
Installation Precautions
12
Installation Space
13
Warning Label
14
Chapter 1 Before Using this Machine
15
Preparation
16
Assembling the Legs and Sheet Basket
16
Attaching the Cutter Guard
16
Installing Cutting Software and Plotter Driver
20
Installing the Firmware Updater
21
Part Names and Functions
23
Front
23
Rear
25
Carriage
27
Pinch Rollers and Grit Rollers
28
SHEET Sensor
28
Clamp
28
Tray
29
Operating Panel
30
Connect Host Computer to Machine
33
Using a USB Cable
33
Using a LAN Cable
33
Using an RS-232C Cable
34
Connecting the Power Cable
36
Turning on the Power
38
Turning off the Power
38
System Configuration
40
Chapter 2 Cutting
41
Cutting Process
42
Loading a Sheet
44
Loading a Leaf Sheet (Cut Sheet)
47
Loading a Roll Sheet (CG-60AR)
48
Loading a Roll Sheet (CG-100/130AR)
52
Pinch Roller Position/Number and Clamp Settings
55
Installing Tools
59
Using the Cutter
59
Using a Pen
63
Using the Creasing Tool
67
Selecting Tool Conditions
68
Setting Tool Conditions
69
Test Cutting
72
Cut the Data
73
Setting the Origin
73
Starting Cutting
73
Pausing Cutting
74
Aborting Cutting (Data Clear)
74
Retracting the Carriage
74
Separating Sheets (Manual Cutting)
75
Chapter 3 Cutting Data with Register Marks
77
Process for Cutting Data with Register Marks
78
Process for Cutting Data with Register Marks.78
78
Creating Register Marks
80
Register Marks
80
Register Mark Size
81
Spacing between Register Marks
82
Reading Range of Register Marks
82
Plotting Areas Around Register Marks
84
Register Mark Detection Precautions
84
Setting Register Mark Detection Conditions
85
Notes on Register Mark Detection Setting Items
85
Detect Register Marks
89
Checking Sheet Tilt Using the LED Pointer
89
Checking Sheet Tilt Using the LED Pointer . 8
89
Detecting Register Marks Using Full-Automatic Detection
90
Detecting Register Marks Using Semi-Automatic Detection
92
Detecting Register Marks Automatically after Sheet Detection
95
ID Cut Process
97
Chapter 4 Helpful Tips
99
Jog Mode Functions
100
2-Point Line Correction [AXIS CORRECT]
100
Cut Area Setting [CUT AREA]
101
Digitizing [DIGITIZE]
101
Length Correction [DIST.COMP.]
103
Cutting Multiple Copies of the same Data [No. COPIES]
106
Expanding the Cutting Area [EXPANDS]
108
Selecting the Cutting Movement Direction [ROTATION]
109
Setting Rotation
109
Divided Cutting [Divisioncut]
111
Y Direction (Width Direction) Divided Cutting
112
Direction (Feed Direction) Divided Cutting
114
Changing the Cutting Sequence [SORTING]
116
Setting Sorting
117
Sorting Procedure
117
Operating the Main Unit Panel Remotely [R.CONTRL]
118
Other Useful Functions
119
Sheet Feed
119
Pause [HOLD]
119
Feed Settings [FEED OPTION]
120
Preventing Uncut Media [OVER CUT/CORNER CUT]
121
Preventing Uncut Media [OVER CUT/ CORNER CUT]
121
Configuring the Network Settings [NETWORK]
122
Event Email Function Settings [EVENT MAIL]
124
Outputting the Settings List [LIST]
128
Copying Settings from Other User Settings [CONFIG COPY]
129
Restoring Default Settings [SETUP RESET]
129
Changing Users [USER CHANGE]
129
Outputting Received Data as ASCII Code [DUMP]
130
Selecting the Screen Display Language [DISPLAY]
130
Checking Machine Information [INFORMATION]
130
Chapter 5 Settings
133
Function
134
Set up
135
Chapter 6 Maintenance
141
Maintenance Precautions
142
Maintenance Items and Timing
143
Items Required for Maintenance
143
Maintenance Procedure
144
Cover (Exterior) Cleaning
144
Cleaning the Y-Bar Rail Surfaces
145
Cleaning the Grit Rollers
146
Cleaning the Pinch Rollers
146
When Not in Use for Extended Periods
146
Consumable Item Replacement
147
Cutter Replacement
147
Pinch Roller Replacement
147
Pen Line Rubber Replacement
148
Chapter 7 Options
152
Sheet Tables and Cutting Sheet
152
Attaching the Sheet Tables
152
Loading a Sheet on the Cutting Sheet
153
Cutting
154
Storing the Cutting Sheet
157
Chapter 8 Dealing with Problems
160
Troubleshooting
160
Checking Register Mark Sensor Responsiveness
162
Aligning the Register Mark Sensor Position
164
Investigating the Cause of Cutting Failures
165
Problems Indicated by Messages
167
Error Messages
167
Display Message List
170
Chapter 9 Appendix
173
Specifications
174
Repetition Accuracy Conditions
176
Setting Sheet
177
Other manuals for MIMAKI CG-AR Series
Care And Maintenance
16 pages
Safety Precautions
12 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the MIMAKI CG-AR Series and is the answer not in the manual?
Ask a question
MIMAKI CG-AR Series Specifications
General
Brand
MIMAKI
Model
CG-AR Series
Category
Plotter
Language
English
Related product manuals
MIMAKI CG-60SR
144 pages
MIMAKI CG-60SL
112 pages
MIMAKI CG-60st
32 pages
MIMAKI CG-60AR
184 pages
MIMAKI CG-130AR
184 pages
MIMAKI CG-60SRIII
172 pages
MIMAKI CG-130FXII
152 pages
MIMAKI CG-130SRIII
172 pages
MIMAKI CG-FX SERIES
142 pages
MIMAKI CF-0912
170 pages
MIMAKI CF-1215
170 pages
MIMAKI CFL-605RT
170 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
