Mitsubishi F700 Series User Manual

62
Parameter list
Power failure stop
261
Power failure stop selection 0, 1, 2, 21, 22 1 0 151
262
Subtracted frequency at deceleration
start
0 to 20Hz 0.01Hz 3Hz 151
263
Subtraction starting frequency 0 to 400Hz, 9999 0.01Hz 50Hz 151
264
Power-failure deceleration time 1 0 to 3600/ 360s 0.1/0.01s 5s 151
265
Power-failure deceleration time 2
0 to 3600/ 360s,
9999
0.1/0.01s 9999 151
266
Power failure deceleration time
switchover frequency
0 to 400Hz 0.01Hz 50Hz 151

267
Terminal 4 input selection 0, 1, 2 1 0 166

268
Monitor decimal digits selection 0, 1, 9999 1 9999 136

269
Parameter for manufacturer setting.
Do not set.
Password
function
296
Password lock level
0 to 6, 99, 101 to 106,
199, 9999
1 9999 187
297
Password lock/unlock
(0 to 5), 1000 to 9998,
9999
1 9999 187

299
Rotation direction detection selection
at restarting
0, 1, 9999 1 9999 147
RS-485 communication
331
RS-485 communication station
number
0 to 31
(0 to 127, 0 to 247)
10209
332
RS-485 communication speed
3, 6, 12, 24, 48, 96, 192,
384
(96, 192, 384, 768)
196209
333
RS-485 communication stop bit
length
0, 1, 10, 11 1 1 209
334
RS-485 communication parity check
selection
0, 1, 2 1 2 209
335
RS-485 communication retry count 0 to 10, 9999 1 1 209
336
RS-485 communication check time
interval
0 to 999.8s, 9999 0.1s 0s 209
337
RS-485 communication waiting time
setting
0 to 150ms, 9999 1ms 9999 209
338
Communication operation command
source
0, 1 1 0 199
339
Communication speed command
source
0, 1, 2 1 0 199
340
Communication startup mode
selection
0, 1, 2, 10, 12 1 0 198
341
RS-485 communication CR/LF
selection
0, 1, 2 1 1 209
342
Communication EEPROM write
selection
0, 1 1 0 211
343
Communication error count  10227

390
% setting reference frequency 1 to 400Hz 0.01Hz 50Hz 242
PLC function
414
PLC function operation selection 0, 1 1 0 255
415
Inverter operation lock mode setting 0, 1 1 0 255
Remote
output
495
Remote output selection 0, 1, 10, 11 1 0 132
496
Remote output data 1 0 to 4095 1 0 132
497
Remote output data 2 0 to 4095 1 0 132

498
PLC function flash memory clear 0 to 9999 1 0 255

502
Stop mode selection at
communication error
0 to 3 1 0 211
Function Parameters
Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting

Mitsubishi F700 Series Specifications

General

Humidity	95% RH or less (non-condensing)
Control Method	V/F control
Protection Features	Overcurrent, overvoltage, undervoltage, overheat, short circuit
Communication Options	RS-485
Operating Temperature	-10°C to +50°C
Storage Temperature	-20°C to +65°C
Altitude	Up to 1000m above sea level
Overload Capacity	150% for 60 seconds
Cooling Method	Forced air cooling
Power Range	0.75 to 630 kW (1 to 845 hp)
Output Voltage	3-phase 200 to 240 VAC, 380 to 500 VAC (matching input voltage)