Panasonic EBL128

To Next Page

To Previous Page

Panasonic Eco Solutions Nordic AB

MEW01623 Rev: - EBL128 Operating Instructions V2.0.x

configurations, on-line status checking, etc. A special password is

required.

Main Page

Default Chapter1
- Operating Instructions1
- Table of Contents3
1 Introduction9
2 Definitions / Explanations11
- Pesn Ab11
- Alarm Point11
- Output Unit12
- Output / Control Output12
- Short Circuit Isolator12
- Display Unit (D.U.)12
- COM Loop12
- Control Unit (C.U.) / C.I.E12
- Fire Brigade Panel (FBP)12
- Control Panel (CP)13
- Led13
- External Indicator (LED)13
- Display / LCD13
- Door Open / Key Switch13
- Site Specific Data (SSD)13
- Software (S/W) / Firmware / System Program13
- Eblwin13
- Web-Server13
3 Overview14
- The EBL128 C.I.e14
- S/W Versions14
- Documents14
- Applications14
- Pc S/W14
4 Control & Indicating Equipment16
5 LED Indicators and Push Buttons18
6 Normal Operation23
- The Display in EBL12823
  - LCD Backlight23
  - The LCD Information Priority Order23
7 User Level, User Name & Password25
- User Level 126
- User Level 2A26
- User Level 2B27
- User Level 2C28
- User Level 3A29
- Access Level 3B29
- Access Level 429
8 Silence Alarm Devices31
- Silence Alarm Devices (Inside Switch)32
- New Zealand FB Silence Switch (Outside Switch)32
9 Disable / Re-Enable Alarm Devices34
10 "Silence Buzzer35
- Buzzer35
11 Disable / Re-Enable All Control, Extinguishing, Ventilation and Interlocking Outputs36
12 Evacuate, Alert Annunciation Acknowledge and Disable37
- Evacuate37
- Alert Annunciation Acknowledge37
- Disable37
13 German Functions / Units38
- Push-Button "ÜE Prüfen38
- Button "Brandfall Steuerungen Ab38
- Indication "Brandfall Steuerungen Ab39
- Button "Akustische Signale Ab39
- Indication "Akustische Signale Ab39
  - Indication in Button "Akustische Signale Ab39
- The Buzzer in the C.I.e39
- Button "ÜE Ab39
- Indication "ÜE Ab40
- Disablements of Outputs; Information in the C.I.e. and FAT Display Respectively40
14 Door Open41
- LED "Door Open41
- Outputs for Routing Equipment (Fire Brigade Tx and Fault Tx)41
- Silence Buzzer41
15 Technical Address / Presentation Number42
- Technical Address for COM Loop Units42
- Presentation Number42
16 Alarm Types43
- Pre-Warning43
- Fire Alarm44
- Heavy Smoke Alarm / Heavy Heat Alarm51
- Key Cabinet Alarm52
  - Key Cabinet Opened before a Fire Alarm52
  - Key Cabinet Opened in Conjunction with a Fire Alarm53
- Quiet Alarm53
- Alarm Acknowledgement Facility (AAF)53
17 Alarm Reset55
- Pre-Warning Reset55
- Fire Alarm Reset55
- Heavy Smoke / Heat Alarm Reset57
- Key Cabinet Alarm Reset57
- Quiet Alarm Reset57
- Alarm Acknowledgement Facility (AAF) Reset57
- Acknowledged Alarm58
- Isolated Alarm58
18 Fault59
- Fault Messages60
- Fault Acknowledge72
19 Commissioning an EBL12873
20 SSD Programming & Download74
- SSD Programming74
- Auto Generating SSD74
- SSD Download74
- Download of Alarm Texts76
21 Software (S/W) Download77
- Download of S/W in EBL128 (C.I.e.)77
- Earlier S/W Version Download78
- S/W Download in Display Units78
22 Restart79
- Boot Menu81
23 Access83
24 Perform Monthly Test (H1)85
25 Disable or Re-Enable (H2)87
- Disable Zone (H2/B1)88
- Disable Zone / Address (H2/B2)89
- Disable Output (H2/B3)90
- Disable All Control, Ventilation, Exting or Interlocking Outputs (H2/B4)92
- Re-Enable Zone (H2/B5)93
- Re-Enable Zone / Address (H2/B6)94
- Re-Enable Output (H2/B7)95
- Re-Enable All Control, Ventil, Exting or Interlocking Outputs (H2/B8)97
- Disable / Re-Enable Alarm Devices (H2/B9)98
- Disable / Re-Enable Outputs for Routing Equipment (H2/B10)9799
- Disable / Re-Enable Alert Annunciation Function (H2/B11)100
26 Set Calendar and Clock (H3)101
- Daylight Saving Time102
27 Present System Status (H4)103
- Disablement (H4/U1)103
- Disablement by Time Channel (H4/U2)104
- Sensor Values (H4/U3)105
  - Reset of a Week Average Sensor Value108
- Sensors Activating SERVICE Signal (H4/U4)109
- Technical Warning (H4/U5)110
- Event Log (H4/U6)111
- Version and Alarm Counter (H4/U7)112
28 Service (H5)113
- Calibration of Supervised Outputs (H5/A1)114
- Sensitive Fault Detection Mode (H5/A2)116
- Service Mode for COM-Loop (H5/A3)117
- Display Current Consumption in Unit (H5/A4)119
- Display Current Consumption on COM-Loop (H5/A5)120
- Display Statistics for COM Loop (H5/A6)121
- Activate Address Setting Mode for du (H5/A7)122
- Show Information about Site Specific Data (H5/A8)123
29 FAULT Acknowledge (H6)125
30 Perform ZONE TEST (Test Mode) (H7)126
31 Maintenance (H8)128
- Disconnect / Re-Connect COM Loop (H8/S1)128
- Disconnect / Re-Connect Zone Line Input (H5/A2)129
- Disconnect / Re-Connect Addressable Zone Interface Input130
- Acknowledge SERVICE Signal (H8/S4)131
- Restore Weekly Average to Default (H8/S5)132
- Test of Alarm Devices (H8/S6)133
- Safe Shut down of Control Unit (H8/S7)134
- Activate Zone-Address in Alarm Mode (H8/S8)135
- Activate Output (H8/S9)137
- Reset Activated Output (H8/S10)139
32 Interlocking Outputs and Inputs (H9)140
- Activated Interlocking Outputs/Inputs (H9/C1)140
- Activate Interlocking Output (H9/C2)141
- Reset Interlocking Output (H9/C3)142
- Disable Interlocking Output (H9/C4)143
- Re-Enable Interlocking Output (H9/C5)144
33 Change Password (H10)145
34 Annual Control146
35 Battery Maintenance147
36 How to Avoid Unnecessary (Nuisance) Fire Alarms148
37 Revision History150

Table of Contents

Other manuals for Panasonic EBL128

Related product manuals