RL78/F13, F14 CHAPTER 33 INSTRUCTION SET
R01UH0368EJ0210 Rev.2.10 1677
Dec 10, 2015
Table 33-5. Operation List (17/18)
Notes 1. Number of CPU clocks (f
CLK) when the internal RAM area, SFR area, or extended SFR area is accessed, or
when no data is accessed.
2. Number of CPU clocks (f
CLK) when the program memory area is accessed.
3. This indicates the number of clocks “when condition is not met/when condition is met”.
Remark Number of clock is when program exists in the internal ROM (flash memory) area. If fetching the instruction from
the internal RAM area, the number becomes double number plus 3 clocks at a maximum.
Instruction
Group
Mnemon
ic
Operands Bytes Clocks Clocks Flag
Note 1 Note 2 Z AC CY
Stack
manipulate
PUSH PSW 2 1
(SP 1) PSW, (SP 2) 00H,
SP SP2
rp 1 1
(SP 1) rpH, (SP 2) rpL,
SP SP – 2
POP PSW 2 3
PSW (SP+1), SP SP + 2 R R R
rp 1 1
rpL (SP), rpH (SP+1), SP SP + 2
MOVW SP, #word 4 1
SP word
SP, AX 2 1
SP AX
AX, SP 2 1
AX SP
HL, SP 3 1
HL SP
BC, SP 3 1
BC SP
DE, SP 3 1
DE SP
ADDW SP, #byte 2 1
SP SP + byte
SUBW SP, #byte 2 1
SP SP byte
Unconditio
nal branch
BR AX 2 3
PC CS, AX
$addr20 2 3
PC PC + 2 + jdisp8
$!addr20 3 3
PC PC + 3 + jdisp16
!addr16 3 3
PC 0000, addr16
!!addr20 4 3
PC addr20
Conditional
branch
BC $addr20 2 2/4
Note3
PC PC + 2 + jdisp8 if CY = 1
BNC $addr20 2 2/4
Note3
PC PC + 2 + jdisp8 if CY = 0
BZ $addr20 2 2/4
Note3
PC PC + 2 + jdisp8 if Z = 1
BNZ $addr20 2 2/4
Note3
PC PC + 2 + jdisp8 if Z = 0
BH $addr20 3 2/4
Note3
PC PC + 3 + jdisp8 if (ZCY)=0
BNH $addr20 3 2/4
Note3
PC PC + 3 + jdisp8 if (ZCY)=1
BT saddr.bit, $addr20 4 3/5
Note3
PC PC + 4 + jdisp8 if (saddr).bit = 1
sfr.bit, $addr20 4 3/5
Note3
PC PC + 4 + jdisp8 if sfr.bit = 1
A.bit, $addr20 3 3/5
Note3
PC PC + 3 + jdisp8 if A.bit = 1
PSW.bit, $addr20 4 3/5
Note3
PC PC + 4 + jdisp8 if PSW.bit = 1
[HL].bit, $addr20 3 3/5
Note3
6/7 PC PC + 3 + jdisp8 if (HL).bit = 1
ES:[HL].bit,
$addr20
4 4/6
Note3
7/8 PC PC + 4 + jdisp8 if (ES, HL).bit = 1
To Next Page
Loading...
Need help?
General
