Operating Instructions M90 Fusion Splicer
Issue 02/97 Index
Index
A
AC Power Cord.................................................6-3
AC Power Fuse...............................................7-26
Accessories ...............................................1-3, 8-2
Accuracy of the Attenuation Display..................5-9
Activating the splice memory...........................4-23
Activating the tension test ...............................4-22
Additional time ..................................................5-6
Are the Flaps Closed?.......................................6-4
Assessing the end face quality........................4-20
Assessing the Fiber End Face Quality.............2-10
Assessing the Splice and Repeating Fusion....4-21
Attenuation .......................................................5-6
Attenuation display............................................5-5
Attenuation Splice / Automatic ........................4-19
Attenuation Splice / Fully Automatic................4-18
Attenuation Splice with Standard Single-Mode
Fibers ..........................................................5-3
Attenuation too high, repeat fusion....................5-5
Attenuation too low ...........................................5-5
Automatic fiber positioning ................................1-3
Automatic Fusion / Automatic............................4-7
Automatic Fusion / Fully Automatic ...................4-6
Automatic Fusion / Manual................................4-9
Automatic Fusion / Semi-Automatic ..................4-8
Automatic fusion time control ............................1-3
B
Basic procedure for troubleshooting
and fault elimination .....................................7-2
Battery..............................................................8-4
Battery Connecting Cable .................................8-6
Button functions.........................................3-2, 4-3
C
Call the menu....................................................3-2
Care / Maintenance.........................................7-24
Case Lid ..................................................1-11, 6-5
Changing the AC power fuse...........................7-26
Changing the battery fuse .................................8-8
Characteristics..................................................8-9
Charging the battery .........................................8-4
Checking the electrodes....................................2-7
Checking the fiber guide..................................2-11
Cinch Plug ........................................................1-9
Cleaning ...........................................................2-9
Cleaning the Electrodes ..................................7-30
Cleaning the fiber guide...................................7-28
Cleaning the Groove .......................................7-27
Cleaning the mirrors and optical lenses ...........7-24
Cleaning the Splicer ..........................................6-3
Cleanliness .....................................................2-13
Cleave length....................................................2-9
Cleave quality..................................................2-10
Cleaver ....................................................6-4, 8-10
Cleaving............................................................2-9
Close the Flaps of the Fusion Unit.....................6-4
Closing the flaps..............................................2-12
Closure Cap of Case Housing ...........................8-7
Coil the AC Power Cord to a Diameter
of Approx. 10 cm..........................................6-3
Connecting the Battery......................................8-7
Connecting the Plug........................................1-10
Connecting the Working Light............................2-4
Control panel.....................................................1-8
Control Panel Buttons .......................................1-8
Crimping Device................................................8-9
D
Data output .......................................................3-8
Date, time .........................................................3-9
Default parameters............................................3-3
Definition of X, Y, Z directions ..........................1-4
Dependency of the parameters on
the required attenuation................................5-7
Description of the Attenuation Splice Program...5-3
Description of the programs...............................3-6
Description of the splicing parameters ...............3-7
Detecting interfering light.................................4-20
Detecting the end angle...................................4-20
Displaying the splice memory on the monitor...4-23
E
Example of a Splicing Curve..............................3-6
Exchanging / cleaning the electrodes...............7-29
External LID input............................................1-10
External video output.........................................1-9
F
Fault message "Bad cleavage"..........................5-4
Fault messages on the monitor .......................7-12
Fiber diameter...................................................1-3
Fiber Direction...................................................1-4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
To Next Page
Loading...