M90 Fusion Splicer Operating Instructions
Index Issue 02/95
Fiber Types that can be Used...........................5-3
Fitting the New Fiber Guide ..............................2-8
Fixed Parameters (LID) / Automatic................ 4-15
Fixed Parameters (LID) / Fully Automatic........ 4-14
Fixed Parameters (LID) / Manual .................... 4-17
Fixed Parameters (LID) / Semi-Automatic.......4-16
Fixed Parameters (Video) / Automatic............. 4-11
Fixed Parameters (Video) / Fully Automatic ....4-10
Fixed Parameters (Video) / Manual................. 4-13
Fixed Parameters (Video) / Semi-Automatic.... 4-12
Flexible software...............................................1-3
Fully automatic .................................................4-4
Further information ...........................................8-9
Fuse again...................................................... 4-22
Fuses ............................................................. 1-13
Fusion current...................................................5-6
Fusion Process.................................................5-4
Fusion program groups.....................................4-3
Fusion sequence ..............................................5-5
Fusion Splicer Modules.....................................1-4
Fusion Unit .......................................................1-6
Fusion using End Face Preparation
with Basic Cleavers....................................4-20
G
Good Splice....................................................4-21
H
Heatshrink Oven, Adjustable.............................8-9
I
Image Area with Reference Line and
Monitor Display...........................................1-8
Index-matching fluid........................................2-13
Inputs ...............................................................1-9
Inserting Fibers of Type "Depressed Inner
Cladding"...................................................2-14
Inserting Fibers of Type "Depressed Inner
Cladding"...................................................7-10
Inserting the Fiber into the Fiber Guide.. 2-11, 2-12
Inserting the fibers................................. 2-11, 2-13
Inserting the Optical Fibers into
the Fiber Holder.........................................2-11
Inserting the Optical Fibers into
the LID System.......................................... 2-13
Installing / exchanging the battery..................... 8-5
Installing the Battery .........................................8-6
Installing the Cleaver ......................................8-10
L
Lead.................................................................5-6
Level display.....................................................5-5
LID performance check...................................2-14
LID system...............................................1-6, 7-27
Lifting Off the Top Panel .................................7-25
Location of the Electrodes and the
Optical Parts to be Cleaned........................7-24
M
Mains Switch.....................................................2-5
Making an Attenuation Splice............................5-4
Menu Item "Additional Functions"......................3-8
Menu Item "Program Selection".........................3-5
Metering the Index-Matching Fluid...................2-13
Modular units ....................................................1-4
Modular Units....................................................1-4
Monitor..............................................................1-8
Monitor and Control Panel.................................1-8
Move Cleaver to Transport Position...................6-4
O
Open the flaps ................................................2-11
Opening the case..............................................2-3
Opening the Eccentric Clamp............................2-8
Opening the Flaps in the Correct Sequence ....2-11
Opening the top panel.....................................7-25
Operation of the Attenuation Splice Program.....5-4
Ordering Numbers.............................................8-2
Other parameters..............................................5-6
Other Tools.....................................................1-13
Outputs.............................................................1-9
P
Parameter Menu ...............................................3-2
Parameter optimization for multimode fibers......7-4
Parameter optimization for single-mode fibers...7-2
Parameter Setting.............................................5-6
Parameter setting for special fiber types............5-7
Pigtail adapters .................................................1-7
Pin Assignment 9 - 25-Pin...............................4-24
Pin Assignment 9 - 9-Pin.................................4-24
Place Tools in the Tool Bag...............................6-3
Positioning ......................................................4-20
Possible problems.............................................5-8
Power Supply.............................................1-5, 2-3
Preparing fibers.................................................5-4
Preparing the Optical Fibers..............................2-9
Principle of the LID System...............................1-6
Printing out the splice values...........................4-24
Procedure for determining the optimum
parameters...................................................5-6
Program overview .............................................3-4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
To Next Page
Loading...