2-12 PERIODIC MAINTENANCE
(EXHAUST SIDE)
MEASURED
TAPPET
CLEARANCE
(mm)
SUFFIX
NO.
120 125 130 135
140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220
PRESENT
SHIM SIZE
(mm)
1.20 1.25 1.30 1.35
1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05
1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.100.10-0.14
SPECIFIED CLEARANCE/NO ADJUSTMENT REQUIRED
0.15-0.19
1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.20
0.20-0.30
1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.31-0.35
1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.36-0.40
1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.41-0.45
1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.46-0.50
1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.51-0.55
1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.56-0.60
1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.61-0.65
1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.66-0.70
1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.71-0.75
1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.76-0.80
1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.81-0.85
1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.86-0.90
1.95 2.00 2.05 2.10 2.15 2.20
0.91-0.95
2.00 2.05 2.10 2.15 2.20
0.96-1.00
2.05 2.10 2.15 2.20
1.01-1.05
2.10 2.15 2.20
1.06-1.10
2.15 2.20
1.11-1.15
1.16-1.20
1.21-1.25 2.20
0.05-0.09
1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
TAPPET SHIM SET (12800-05820)
TAPPET SHIM SELECTION TABLE [EXHAUST]
TAPPET SHIM NO. (12892-05C00-XXX)
HOW TO USE THIS CHART:
I. Measure tappet clearance. “ENGINE IS COLD”
II. Measure present shim size.
III. Match clearance in vertical column with present shim size
in horizontal column.
EXAMPLE
Tappet clearance is 0.33 mm
Present shim size 1.70 mm
Shim size to be used 1.80 mm
To Next Page
Loading...
