Specifications-Type
453/R453
Characteristic
Performance Requirement
0°
C to
-15°
C to
+40°
c
+55°
C
Voltage Accuracy
+l
%
+ l .5%
Current Accuracy
-1-l
%
+l.5%
Repetition Rate
+0.5%
+l
%
Accuracy
Risetime
Less
than
l
microsecond
Duty
Cycle
49% to
51
%
Output Resistance Approximately
200 ohms
in
l v
position
Approximately
20
ohms
in
0.1
V
position
Z AXIS INPUT
Characteristic Performance Requirement
Sensitivity
5 volt peak to peak signal pro-
duces noticeable modulation
Usable Frequency Range
DC
to greater than
50
MHz
Input Resistance
at
DC
Approximately 47
kilohms
Input Coupling
DC
coupled
Polarity of Operation
Positive-going
input signal de-
creases trace intensity
Negative-going input signal
in-
creases trace intensity
Maximum Input Voltage
200
volts combined
DC
and peak
AC
OUTPUT SIGNALS
Characteristic
A and B
Gate
Waveshape
Amplitude
Polarity
Duration
Output Resistance
Vertical Signal Out
(CH
1
only}
Output Voltage
Bandwidth
Output coupling
Output resistance
Characteristic
Line
Voltage
Voltage Ranges
(AC,
RMS}
115-volts nominal
1-4
Performance Requirement
Rectangular pulse
12
volts peak, + l 0%
Positive-going with baseline
at
about
-0.7
volts
Same duration as the
respective
sweep
Approximately 1.5
kilohms
25
millivolts, or
greater/division
of
CRT
display into
1 megohm
load
DC
to
25
MHz
or greater when
cascaded with Channel 2 or into
50-ohm load
DC
coupled
Approximately
50
ohms
POWER
SUPPLY
Performance Requirement
115
volts nominal or 230 volts
nom-
inal
90
to 110 volts
l
04
to
126
volts
112
to
136
volts
Characteristic
230-volts nominal
Line
Freauency
Maximum Power Con-
sumption
at
115
volts,
60Hz
Performance Requirement
180
to
220
volts
208
to
252
volts
224 to
272
volts
48
to 440
Hz
92
watts
(l
05
volt-amperes)
CATHODE-RAY
TUBE
(CRT>
Characteristic Performance Requirement
Tube Type
Tektronix T
4530-31-1
rectangular
Phosphor
P31
standard. Others available on
special order.
Accelerating
Potential Approximately
10
kV
total
Graticule
Type Internal
Area
Six
divisions vertical by l 0 divi-
sions
horizontal.
Each
division
equals
0.8
centimeter.
Illumination
Variable edge lighting
Unblanking
Bias-type,DC coupled to
CRT
grid.
Raster Distortion
0.1
division or
less
total.
Trace Finder
Limits
display within graticule
area
when pressed.
ENVIRONMENTAL
The
following environmental test
limits
apply when tested
in
accordance
with
the recommended test procedure.
This
instrument
will
meet the electrical characteristics given
in
this
section following environmental test. Complete details
on environmental test procedures, including failure criteria,
etc., may be obtained
from
Tektronix,
Inc.
Contact your
loca I Tektronix
Field
Office or representative.
Characteristic
Performance Requirement
Temperature
Operating
-15°
C to
+55°
C
Non-operating
-55°
C to
+75°
C
Altitude
Operating
15,000 feet maximum
Non-operating
50,000 feet maximum
Humidity
Five
cycles
(120
hours}
to
95%
Operating
and
relative
humitity referenced
to
storage
Mil-E-l
6400F.
Vibration
Operating
and
15
minutes along each of the three
non-operating major axes
at
a total displacement
of 0.025-inch peak to peak
(4
g
at
55
c/s) with frequency varied
from
10-55-10
c/s
in
one-minute cycles.
Hold
at
55
c/s
for three minutes on
each axis.
Shock
Operating
and
Two
shocks
at
30 g, one-half sine,
non-operating
11
millisecond duration each direc-
tion along each major axis.
Gui
I-
lotine-type
shocks. Total of
12
shocks.
©
To Next Page
Loading...
Need help?
General
