Tektronix 453 - Page 237

Fig. &
Index
Tektronix
No. Part No.
6-71 352-0031-00
------
-72 211-0538-00 20000
-73 210-0006-00 20000
210-0054-00 33320
-74 210-0407-00 20000
21 0-0406-00 33320
-75 670-0414-04
------
388-0641-02
-76 214-0506-00
-77 214-0579-00
-78 136-0183-00
-79 136-0220-00
------
-80
211-0116-00
-81 179-0995-02
------
131-0371-00
-82 386-0202-01
-83 348-0064-00
-84
348-0056-00
-85 348-0055-00
-86 131-0181-00
------
358-0136-00
-87 343-0002-00
------
-88 211-0507-00
-89 21 0-0863-00
-90 210-0457-00
-91 129-0069-00
------
361-0007-00
-92 210-0201-00
------
213-0044-00
-93 214-0317-00
-94
352-0062-00
------
211-0033-00
211-0012-00
21 0-0004-00
210-0406-00
®
Mechanical Parts List-Type 453/R453
FIG. 6 REAR CHASSIS (cont)
Serial/ Model No.
Eff
Disc
33319X
33319
33319
Q
t
y 1 2 3 4 5
Description
2
HOLDER, fuse, single
mounting hardware for each: (not included w/holder)
2
SCREW, 6-32 x
5
/
16
inch, l 00° csk, FHS
2 LOCKWASHER, int~rnal, #6
2 LOCKWASHER, #4 split
2
NUT, hex., 6-32 x 114 inch
2 NUT, hex., 4-40 x
3
/
16
inch
ASSEMBLY, circuit board-Z AXIS
assembly includes:
1
BOARD, circuit
20
PIN, connector
3
PIN, test point
4 SOCKET, transistor, 3 pin
4
SOCKET, transistor, 3 pin
mounting hardware: (not included w/socket)
3
SCREW, sems, 4-40 x
5
/
16
inch, PHB
CABLE HARNESS, A sweep
cable harness includes:
37
CONNECTOR, single contact, female
1
PLATE, center bulk head
2
GROMMET, plastic, % inch
2
GROMMET, plastic, 0.354 ID x 0.406 inch OD
1
GROMMET, plastic,
1
/
4
inch
1
CONNECTOR, terminal, standoff
mounting hardware: (not included w/connector)
BUSHING, plastic
CLAMP, cable,
3
/
1
.
6
inch
mounting hardware: (not included w/clamp)
SCREW, 6-32 x
5
/
16
inch, PHS
WASHER, "D" type, 0.191 ID x
3
%
4
x
33
/
64
inch long
NUT, keps, 6-32 x
5
/
1
.
6
inch
3
POST, terminal, tie off
mounting hardware for each: (not included w/post)
SPACER, plastic, 0.188 inch long
LUG, solder, SE #4
mounting hardware: (not included w/lug)
SCREW, thread forming, 5-32 x
3
/
16
inch, PHS
2 HEAT SINK
2
HOLDER, heat sink
mounting hardware for each: (not included w/holder)
2
SCREW, sems, 4-40 x
5
/
16
inch, PHS
2
SCREW, 4-40 x % inch, PHS
4 LOCKWASHER, internal, #4
4
NUT, hex., 4-40 x
3
/
16
inch
9-19