To Next Page

To Previous Page

197

34. WARNING AND ERROR MESSAGES

Too short

Input password has fewer than 3 characters. Password must have 3 or more characters and 8 or fewer

characters.

USB error

An error has occurred in loading or saving data to USB flash drive.

USB full !

There is no more room to enter data on USB flash drive.

USB not found

USB flash drive was removed during USB mode operation.

********

The calculated result is too large to be displayed on the screen in its totality.

Table of Contents4
Precautions for Safe Operation7
Precautions10
Laser Safety Information13
Product Outline15
Parts of the Instrument15
Mode Structure18
Bluetooth Wireless Technology/Wireless LAN19
Basic Operation21
Basic Key Operation21
Display Functions24
Starkey Mode26
Using the Battery27
Battery Charging27
Installing/Removing the Battery28
Setting up the Instrument29
Centering29
Levelling30
Power On/Off32
Connecting to External Devices34
Wireless Communication Using Bluetooth Technology34
Communication between the GM and Companion Device36
Connection Via RS232C Cable38
Target Sighting and Measurement39
Manually Sighting the Target39
Angle Measurement40
Measuring the Horizontal Angle between Two Points (Horizontal Angle 0°)40
Setting the Horizontal Angle to a Required Value (Horizontal Angle Hold)41
Angle Measurement and Outputting the Data43
Distance Measurement44
Returned Signal Checking44
Distance and Angle Measurement45
Recalling the Measured Data46
Distance Measurement and Outputting the Data46
Coordinate Measurement and Outputting the Data47
REM Measurement48
Coordinate Measurement50
Entering Instrument Station Data and Azimuth Angle50
Setting Instrument Station Coordinate with Resection Measurement55
Coordinate Measurement64
Setting-Out Measurement66
Coordinates Setting-Out Measurement66
Distance Setting-Out Measurement68
REM Setting-Out Measurement70
Setting-Out Line71
Defining Baseline71
Setting-Out Line Point74
Setting-Out Line Line76
Setting-Out Arc78
Defining an Arc78
Setting-Out Arc83
Point Projection85
Defining Baseline85
Topography Observation87
Observation Setting88
Observation89
Offset Measurement92
Single-Distance Offset Measurement92
Angle Offset Measurement93
Two-Distance Offset Measurement94
Plane Offset Measurement96
Column Offset Measurement98
Missing Line Measurement100
Measuring the Distance between 2 or more Points100
Changing the Starting Point103
Surface Area Calculation105
Intersections108
Intersections (Type A)108
Intersections (Type B)116
Traverse Adjustment119
Route Surveying124
Instrument Station Settings124
Straight Line Calculation125
Circular Curve Calculation127
Spiral Curve128
Parabola133
Point Calculation136
Intersection Angle/Azimuth Angle Calculation138
Route Calculation140
Cross Section Survey151
Point to Line MEASUREMENT155
Recording Data - Topo Menu158
Recording Instrument Station Data158
Recording Backsight Point160
Recording Angle Measurement Data161
Recording Distance Measurement Data162
Recording Coordinate Data163
Recording Distance and Coordinate Data164
Reviewing JOB Data165
Recording Notes165
Deleting Recorded JOB Data167
Selecting/Deleting a Job168
Selecting a JOB168
Deleting a JOB169
Registering/Deleting Data171
Registering/Deleting Known Point Data171
Registering/Deleting Codes174
Reviewing Known Point Data174
Reviewing Codes176
Outputting Job Data177
Outputting JOB Data to Host Computer177
Using Usb Flash Drive179
Inserting the USB Flash Drive179
Selecting T Type/S Type180
Storing JOB Data to USB Flash Drive180
Loading Data in USB Flash Drive to the GM182
Displaying and Editing Files183
Formatting the Selected External Memory Media184
Changing the Settings185
Observation Conditions - Angle/Tilt185
Observation Conditions - Dist186
Observation Conditions - Reflector (Target)188
Observation Conditions - Atmosphere189
Observation Conditions - Other190
Instrument Conditions - Power191
Instrument Conditions - Instrument192
Instrument Conditions - Unit193
Instrument Conditions - Password194
Tsshield195
Instrument Conditions - Date and Time195
Allocating Key Functions196
Restoring Default Settings198
Warning and Error Messages200
Checks and Adjustments204
Circular Level204
Tilt Sensor204
Reticle207
Collimation207
Optical Plummet208
Additive Distance Constant210
Laser Plummet211
Cloud Oaf213
Cloud OAF Offline Update213
Power Supply System215
Prism System216
Accessories217
Specifications219
Explanations224
Manually Indexing the Vertical Circle by Face 1/2 Measurement224
Correction for Refraction and Earth Curvature225
Regulations226

Brand	Topcon
Model	GM-100 Series
Category	Measuring Instruments
Language	English

Topcon GM-100 Series User Manual

Table of Contents

Other manuals for Topcon GM-100 Series

Questions and Answers:

Topcon GM-100 Series Specifications

Related product manuals