Need help?Do you have a question about the TP-Link TL-SG5428 and is the answer not in the manual?
Methods to log on to the switch via console port or Telnet/SSH.
Command to create IEEE 802.1Q VLANs and enter VLAN Configuration Mode.
Command to create VLAN Interface and enter Interface VLAN Mode.
Command to configure the Link Type for ports (access, trunk, general).
Command to add an Access port to an IEEE 802.1Q VLAN.
Command to add a Trunk port to IEEE 802.1Q VLANs.
Command to add a General port to IEEE 802.1Q VLAN and specify egress rule.
Command to create Protocol-based VLAN templates.
Command to create a Protocol-based VLAN and bind it.
Command to enable the VLAN-VPN function globally.
Command to enable the dot1q tunnel feature on specified interfaces.
Command to configure a port as the VPN Up-link port.
Command to enable Voice VLAN function.
Command to create Voice VLAN OUI.
Command to configure Voice VLAN mode for Ethernet ports.
Command to enable the Voice VLAN security feature.
Command to configure a designated VLAN as the primary VLAN of Private VLAN.
Command to configure a designated VLAN as the secondary VLAN of Private VLAN.
Command to associate primary VLAN with secondary VLAN.
Command to add host type port to private VLAN.
Command to add promiscuous type port to private VLAN.
Command to add a port to the EtherChannel Group and configure its mode.
Command to configure the Aggregate Arithmetic for LAG.
Command to configure the LACP system priority globally.
Command to configure the LACP port priority for specified ports.
Command to add a new user or modify existing user information.
Command to manually bind IP, MAC, VLAN, and Port number for ARP inspection.
Command to enable DHCP-Snooping function globally.
Command to configure global DHCP-Snooping parameters.
Command to configure a port as a Trusted Port for DHCP packets.
Command to enable MAC Verify feature in DHCP Snooping.
Command to enable Flow Control for DHCP packets.
Command to enable the Decline Protect feature for DHCP packets.
Command to enable the ARP Detection function globally.
Command to configure ports as Trusted Ports for ARP inspection.
Command to enable the ARP Defend function.
Command to configure the ARP speed of a specified port.
Command to configure IP Verify Source mode for a specified port.
Command to enable the DoS defend function globally.
Command to select the DoS Defend Type.
Command to enable the IEEE 802.1X function globally.
Command to configure the Authentication Method of IEEE 802.1X.
Command to enable the Guest VLAN function globally.
Command to configure the control mode of IEEE 802.1X for a port.
Command to configure the control type of IEEE 802.1X for a port.
Command to configure RADIUS parameters.
Command to configure severity level and status for the log buffer.
Command to configure level and status for the log file input.
Command to enable SSH function.
Command to enable SSH protocol version (v1 or v2).
Command to download SSH key file from TFTP server.
Command to enable the SSL function globally for secure HTTPS connections.
Command to download a certificate to the switch from TFTP server.
Command to download an SSL key to the switch from TFTP server.
Command to add a static MAC address entry.
Command to configure aging time for dynamic addresses.
Command to add filtering address entries to forbid undesired packages.
Command to configure Port Security by limiting learned MAC addresses.
Command to configure the system time manually.
Command to configure time zone and NTP server IP address.
Command to configure the management VLAN for switch access.
Command to configure system IP, Subnet Mask, and Default Gateway.
Command to upgrade the switch system file via TFTP server.
Command to enter Interface Configuration Mode for a Gigabit Ethernet port.
Command to configure multiple Gigabit Ethernet ports simultaneously.
Command to enable the flow-control function for a port.
Command to configure the Duplex Mode for an Ethernet port.
Command to configure the Speed Mode for an Ethernet port.
Command to enable broadcast storm control function.
Command to enable multicast storm control function.
Command to enable unicast storm control function.
Command to configure storm control rate for packets.
Command to configure bandwidth limit for an Ethernet port.
Command to configure CoS (Class of Service) based on port.
Command to enable mapping between IEEE802.1P Priority and TC egress queue.
Command to enable mapping between DSCP Priority and CoS value.
Command to configure mapping between IEEE 802.1P priority/VLAN tag, CoS value and TC egress queue.
Command to configure mapping between DSCP Priority and CoS value.
Command to configure the Schedule Mode for queue scheduling.
Command to configure the monitoring port for a monitor session.
Command to configure the monitored ports and their modes (rx, tx, both).
Command to configure the forward port list of a port for communication.
Command to enable the loopback detection function globally.
Command to enable the loopback detection function for a specified port.
Command to configure process-mode and recovery-mode for detected loops.
Command to add Time-Range for ACL rules.
Command to create standard-IP ACL and extend-IP ACL.
Command to create MAC ACL.
Command to add Standard-IP ACL rules.
Command to add Extended-IP ACL rules.
Command to add Policy for controlling data packets.
Command to add ACLs and create actions for a policy.
Command to bind a policy to a specified port.
Command to bind a policy to a VLAN.
Command to enable the STP function globally.
Command to enable STP function for a port.
Command to configure parameters for port comparison in CIST and MST instances.
Command to configure the STP mode (STP, RSTP, MSTP).
Command to access MST Configuration Mode for VLAN-Instance mapping, region name.
Command to configure the bridge priority.
Command to add Community for SNMP authentication.
To Next Page
General