Name: Trojan T2-C
Brand: Trojan
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Spare parts

124 T2-C User Guide

NOTE: The complete spare parts list is available in a separate document and can be acquired

from Trojanlabel or from official Trojanlabel partners. The above part lists only contain the most

common spare parts for reference to help in ordering if necessary. Before ordering any spare

parts, please contact your Trojanlabel distributor or technical support.

T2-I002 Ink Supply Tube with Coupling Grande

Magenta

T2-I003 Ink Supply Tube with Coupling Grande

Yellow

T2-I004 Ink Supply Tube with Coupling Grande

Black

TTL-232R-3V3-AJ USB to 3.5 mm mini jack cable

Part Number Description

Default Chapter7
- Table of Contents7
Chapter 1: Introduction11
- General Information11
Introduction11
- Overview and Application12
Chapter 2 Setting up the T2-C Press17
- Cabling (Network and Power Supply)18
- Physical Setup17
Chapter 3: Power on19
Power on19
- Power on Process19
- Visible Safety Check19
- Installing Ink Tanks and the Printhead20
Chapter 4 Loading the Label Material29
- Unwinder and Rewinder Roll Direction29
  - Rolling Direction Unwinder - Ink Jet Coating on the Inside or Outside29
  - Rolling Direction Rewinder30
- Threading the Label Material from Scratch31
- Adjusting the Label Edge Sensor35
- Calibrate Tension for the Label Web35
- Splicing and Changing the Label Roll37
Chapter 5 Select and Queue Print / Start Print Job39
Chapter 6 Pause, Resume, or Stop a Print Job41
Chapter 7 Moving the Label Web43
Chapter 8: Printing Modes45
- Continuous Printing Mode45
Printing Modes45
- Die-Cut Printing Mode46
  - Calibrating the Label Gap Sensor46
- Blackmark Printing Mode48
  - Calibrating the Label Gap/Blackmark Sensor48
- Gap Size and Speeds50
Chapter 9 Shutting down the T2-C Press51
Chapter 10: Driver Installation and Features53
- Driver Installation53
Driver Installation and Features53
- Driver Features and Functions56
  - General Driver Settings57
  - Integrating Additional Color Profiles59
Chapter 11: User Interface (UI)61
- Right Side Status Bar61
User Interface (UI)61
- General Settings (HOME Tab)62
- T2-C Press Handling Menus (Trojantwo Tab)74
Chapter 12: Updating Software and Firmware89
Updating Software and Firmware89
- Updating Via the Online Updater89
- Updating Via the Offline Updater90
- Purpose93
- Usage93
Using the Built in Slitter for the T2-C Press93
Chapter 13: Using the Built in Slitter for the T2-C Press94
- Replacing the Slitter Blades95
Chapter 14: Maintenance97
- Cleaning Other Rollers99
- Emptying the Waste Ink Bottle99
Maintenance97
- Regular Cleaning/Checking Tasks97
  - Cleaning the NIP Roller97
- Replacing the Wiper Roller101
- Manual Printhead Wiping105
- Clean or Replace Aerosol Filter108
Preparing the T2-C Press for Transportation109
- Removing the Printhead109
Chapter 15: Preparing the T2-C Press for Transportation110
- Storing Used or Opened Printheads110
- Removing the Ink from the Reservoir Ink Tanks111
- Removing the Ink from the Ink Filters112
- Empty and Clean the Waste Ink Bottle113
- Removing the Ink Tanks113
Chapter 16: Troubleshooting115
- Error States115
Troubleshooting115
- Error Messages on Screen119
Appendix A: Spare Parts121
- Consumables121
- Print Engine121
- Circuit Boards122
- Tubes, Cables, and Other Parts123
Index125

Brand	Trojan
Model	T2-C
Category	Label Maker
Language	English

Trojan T2-C User Manual

Table of Contents

Questions and Answers:

Trojan T2-C Specifications