YASKAWA U1000 Series - Page 478

B.3 Parameter Table
478 YASKAWA ELECTRIC SIEP C710636 02B YASKAWA U1000 Technical Manual
■ C4: Torque Compensation
■ C5: Automatic Speed Regulator (ASR)
No.(Addr.) Name Description Setting Page
C4-01
(215H)
<10> Default setting is determined by the control mode (A1-02).
<16> Default setting is determined by the control mode (A1-02) and the drive model (o2-04).
Torque Compensation Gain
Sets the gain for the automatic torque (voltage) boost function and helps to produce better
starting torque. Used for motor 1.
Default:
<10>
Min: 0.00
Max: 2.50
221
C4-02
(216H)
Torque Compensation Primary
Delay Time
Sets the torque compensation filter time.
Default:
<16>
Min: 0 ms
Max: 60000 ms
221
C4-03
(217H)
Torque Compensation at Forward
Start
Sets torque compensation at forward start as a percentage of motor torque.
Default: 0.0%
Min: 0.0%
Max: 200.0%
221
C4-04
(218H)
Torque Compensation at Reverse
Start
Sets torque compensation at reverse start as a percentage of motor torque.
Default: 0.0%
Min: -200.0%
Max: 0.0%
221
C4-05
(219H)
Torque Compensation Time
Constant
Sets the time constant for torque compensation at forward start and reverse start (C4-03 and
C4-04).
Default: 10 ms
Min: 0 ms
Max: 200 ms
222
C4-07
(341H)
Motor 2 Torque Compensation
Gain
Sets the torque compensation gain used for motor 2.
Default: 1.00
Min: 0.00
Max: 2.50
222
No.(Addr.) Name Description Setting Page
C5-01
(21BH)
ASR Proportional Gain 1
Sets the proportional gain of the speed control loop (ASR).
Default:
<10>
Min: 0.00
Max: 300.00
224
C5-02
(21CH)
ASR Integral Time 1
Sets the integral time of the speed control loop (ASR).
Default:
<10>
Min: 0.000 s
Max: 10.000 s
224
C5-03
(21DH)
ASR Proportional Gain 2
Sets the speed control gain 2 of the speed control loop (ASR).
Default:
<10>
Min: 0.00
Max: 300.00
224
C5-04
(21EH)
ASR Integral Time 2
Sets the integral time 2 of the speed control loop (ASR).
Default:
<10>
Min: 0.000 s
Max: 10.000 s
224
C5-05
(21FH)
ASR Limit
Sets the upper limit for the speed control loop (ASR) as a percentage of the maximum output
frequency (E1-04).
Default: 5.0%
Min: 0.0%
Max: 20.0%
225
C5-06
(220H)
ASR Primary Delay Time Constant
Sets the filter time constant for the time from the speed loop to the torque command output.
Default:
<10>
Min: 0.000 s
Max: 0.500 s
225
C5-07
(221H)
ASR Gain Switching Frequency
Sets the frequency for switching between proportional gain 1, 2 and integral time 1, 2.
Default:
<10>
Min: 0.0 Hz
Max: 400.0 Hz
225
C5-08
(222H)
ASR Integral Limit
Sets the ASR integral upper limit as a percentage of rated load torque.
Default: 400%
Min: 0%
Max: 400%
225
C5-12
(386H)
Integral Operation during Accel/
Decel
0: Disabled. Integral functions are enabled only during constant speed.
1: Enabled. Integral functions are always enabled, during accel/decel and during constant speed.
Default: 0
Min: 0
Max: 1
225
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
OLV/PM AOLV/PM
CLV
V/f w/PG
CLV/PM
V/f OLV
SIEP_C710636_02B_1_0.book 478 ページ ２０１５年１１月２５日 水曜日 午後４時５６分