E.3 User Setting Table
YASKAWA ELECTRIC
SIEP C710636 02B YASKAWA U1000 Technical Manual 619
F7-05 Subnet Mask 1
F7-06 Subnet Mask 2
F7-07 Subnet Mask 3
F7-08 Subnet Mask 4
F7-09 Gateway Address 1
F7-10 Gateway Address 2
F7-11 Gateway Address 3
F7-12 Gateway Address 4
F7-13 Address Mode at Startup
F7-14 Duplex Mode Selection
F7-15 Communication Speed Selection
F7-16 Communication Loss Time-out
F7-17 EtherNet/IP Speed Scaling Factor
F7-18 EtherNet/IP Current Scaling Factor
F7-19 EtherNet/IP Torque Scaling Factor
F7-20 EtherNet/IP Power Scaling Factor
F7-21 EtherNet/IP Voltage Scaling Factor
F7-22 EtherNet/IP Time Scaling
F7-23 to
F7-32
Dynamic Output Assembly Parameters
F7-33 to
F7-42
Dynamic Input Assembly Parameters
H1-01
Multi-Function Digital Input Terminal S1 Function
Selection
H1-02
Multi-Function Digital Input Terminal S2 Function
Selection
H1-03
Multi-Function Digital Input Terminal S3 Function
Selection
H1-04
Multi-Function Digital Input Terminal S4 Function
Selection
H1-05
Multi-Function Digital Input Terminal S5 Function
Selection
H1-06
Multi-Function Digital Input Terminal S6 Function
Selection
H1-07
Multi-Function Digital Input Terminal S7 Function
Selection
H1-08
Multi-Function Digital Input Terminal S8 Function
Selection
H2-01 Terminal M1-M2 Function Selection (relay)
H2-02
CIMR-UA, CIMR-UD, CIMR-UT:
Terminal P1-PC Function Selection (Open-collector)
CIMR-UB:
Terminal M3-M4 Function Selection (Relay)
H2-03
CIMR-UA, CIMR-UD, CIMR-UT:
Terminal P2-PC Function Selection (Open-collector)
CIMR-UB:
Terminal M5-M6 Function Selection (Relay)
H2-06 Power Consumption Output Unit Selection
H2-07 Memobus Regs1 Address Select
H2-08 Memobus Regs1 Bit Select
H2-09 Memobus Regs2 Address Select
H2-10 Memobus Regs2 Bit Select
H3-01 Terminal A1 Signal Level Selection
H3-02 Terminal A1 Function Selection
H3-03 Terminal A1 Gain Setting
H3-04 Terminal A1 Bias Setting
H3-05 Terminal A3 Signal Level Selection
H3-06 Terminal A3 Function Selection
H3-07 Terminal A3 Gain Setting
H3-08 Terminal A3 Bias Setting
H3-09 Terminal A2 Signal Level Selection
H3-10 Terminal A2 Function Selection
H3-11 Terminal A2 Gain Setting
H3-12 Terminal A2 Bias Setting
H3-13 Analog Input Filter Time Constant
H3-14 Analog Input Terminal Enable Selection
H3-16 Terminal A1 Offset
H3-17 Terminal A2 Offset
H3-18 Terminal A3 Offset
No. Name
User
Setting
H4-01
Multi-Function Analog Output Terminal FM Monitor
Selection
H4-02 Multi-Function Analog Output Terminal FM Gain
H4-03 Multi-Function Analog Output Terminal FM Bias
H4-04
Multi-Function Analog Output Terminal AM Monitor
Selection
H4-05 Multi-Function Analog Output Terminal AM Gain
H4-06 Multi-Function Analog Output Terminal AM Bias
H4-07
Multi-Function Analog Output Terminal FM Signal Level
Selection
H4-08
Multi-Function Analog Output Terminal AM Signal Level
Selection
H5-01 Drive Node Address
H5-02 Communication Speed Selection
H5-03 Communication Parity Selection
H5-04 Stopping Method After Communication Error (CE)
H5-05 Communication Fault Detection Selection
H5-06 Drive Transmit Wait Time
H5-07 RTS Control Selection
H5-09 CE Detection Time
H5-10 Unit Selection for MEMOBUS/Modbus Register 0025H
H5-11 Communications ENTER Function Selection
H5-12 Run Command Method Selection
H5-17 Operation Selection when Unable to Write into EEPROM
H5-18 Filter Time Constant for Motor Speed Monitoring
H6-01 Pulse Train Input Terminal RP Function Selection
H6-02 Pulse Train Input Scaling
H6-03 Pulse Train Input Gain
H6-04 Pulse Train Input Bias
H6-05 Pulse Train Input Filter Time
H6-06 Pulse Train Monitor Selection
H6-07 Pulse Train Monitor Scaling
H6-08 Pulse Train Input Minimum Frequency
L1-01 Motor Overload Protection Selection
L1-02 Motor Overload Protection Time
L1-03 Motor Overheat Alarm Operation Selection (PTC input)
L1-04 Motor Overheat Fault Operation Selection (PTC input)
L1-05 Motor Temperature Input Filter Time (PTC input)
L1-08 oL1 Current Lvl
L1-09 oL1 Current Lvl (for 2nd motor)
L1-13 Continuous Electrothermal Operation Selection
L2-01 Momentary Power Loss Operation Selection
L2-02 Momentary Power Loss Ride-Thru Time
L2-03 Momentary Power Loss Minimum Baseblock Time
L2-04 Momentary Power Loss Voltage Recovery Ramp Time
L2-07
Momentary Power Loss Voltage Recovery Acceleration
Time
L2-13 Power Supply Frequency Fault Detection Gain
L2-21 Low Input Voltage Detection Level
L2-27 Power Supply Frequency Fault Detection Width
L3-01 Stall Prevention Selection during Acceleration
L3-02 Stall Prevention Level during Acceleration
L3-03 Stall Prevention Limit during Acceleration
L3-04 Stall Prevention Selection during Deceleration
L3-05 Stall Prevention Selection during Run
L3-06 Stall Prevention Level during Run
L3-14 Stall Prevention Level during Deceleration
L3-22 Deceleration Time at Stall Prevention during Acceleration
L3-23
Automatic Reduction Selection for Stall Prevention during
Run
L3-27 Stall Prevention Detection Time
L3-36
Vibration Suppression Gain during Acceleration (with
Current Limit)
L3-39
Current-limited Integral Time Constant during
Acceleration
L3-40
Current-limited Maximum S-curve Selection during
Acceleration
No. Name
User
Setting
SIEP_C710636_02B_1_0.book 619 ページ ２０１５年１１月２５日 水曜日 午後４時５６分
To Next Page
Loading...
