YOKOGAWA MX100 - Page 97

4-13
IM MX100-01E
Specification
3
2
1
4
5
Index
The inputs indicated below can be used on MXLOGGER or the MX100/DARWIN API
(software sold separately).
60 mV (high res.)
1 V (high res.)
6 V (high res.)
PLATINEL
PR40-20
NiNiMo
WRe3-25
W/WRe26
Type-N(AWG14)
Cu10 at 20°C
alpha = 0.00392
Cu10 at 20°C
alpha = 0.00393
Cu25 at 0°C
alpha = 0.00425
Cu53 at 0°C
alpha = 0.00426035
Cu100 at 0°C
alpha = 0.00425
Pt25(JPt100*1/4)
Cu10 GE
(high res.)
Cu10 L&N
(high res.)
Cu10 WEED
(high res.)
Cu10 BAILEY
(high res.)
0.000 to 60.000mV
-1.0000 to 1.0000V
0.0000 to 6.0000V
0.0 to 1400.0°C
0.0 to 1900.0°C
0.0 to 1310.0°C
0.0 to 2400.0°C
0.0 to 2400.0°C
0.0 to 1300.0°C
-200.0 to 300.0°C
-200.0 to 300.0°C
-200.0 to 300.0°C
-50.0 to 150.0°C
-50.0 to 150.0°C
-200.0 to 550.0°C
-200.0 to 300.0°C
-200.0 to 300.0°C
-200.0 to 300.0°C
-200.0 to 300.0°C
±(0.05% of rdg + 20 digits)
±(0.05% of rdg + 2 digits)
±(0.05% of rdg + 20 digits)
±(0.05% of rdg + 1°C)
±(0.05% of rdg + 2.5°C)
Except 300 to 700°C: ±6°C
less than 300°C: not guaranteed
±(0.05% of rdg + 0.7°C)
±(0.05% of rdg + 2°C)
Except 0 to 200°C: ±2.5°C
2000°C or higher:
±(0.05% of rdg + 4°C)
±(0.05% of rdg + 2°C)
Except 100 to 300°C: ±4°C
less than 100°C: not guaranteed
±(0.05% of rdg + 0.7°C)
±(0.1% of rdg + 2°C)
±(0.1% of rdg + 0.5°C)
±(0.05% of rdg + 0.3°C)
±(0.1% of rdg + 0.5°C)
±(0.1% of rdg + 2°C)
1 µV
100 µV
100 µV
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
0.1°C
±(0.1% of rdg + 100 digits)
±(0.1% of rdg + 10 digits)
±(0.1% of rdg + 100 digits)
±(0.1% of rdg + 4°C)
±(0.1% of rdg + 12°C)
Except 300 to 700°C: ±25°C
less than 300°C: not guaranteed
±(0.1% of rdg + 2.7°C)
±(0.1% of rdg + 7°C)
Except 0 to 200°C: ±12°C
2000°C or higher:
±(0.1% of rdg + 11°C)
±(0.1% of rdg + 8.5°C)
Except 100 to 300°C: ±12°C
less than 100°C: not guaranteed
±(0.1% of rdg + 3.5°C)
±(0.2% of rdg + 5°C)
±(0.2% of rdg + 2°C)
±(0.1% of rdg + 1.5°C)
±(0.2% of rdg + 2°C)
±(0.2% of rdg + 5°C)
Input
Measurement Accuracy
Integration Time: 16.67 ms
or More
Highest
Resolution
(1 Digit)
Rated
Measurement
Range
Measurement Accuracy
Integration Time: 1.667 ms
Measurement
Range
Type
DC voltage
RTD (Measurement current: 1 mA)
Thermocouple (excludes RJC accuracy, when burnout is OFF)
Measurementinterval,integrationtime,andlter:
Measurement
Interval
100 ms
16.67 ms
20 ms
Auto
Integration
Time
Filter
Rejected Noise and Notes
500 ms
Rectangular
1 s
2 s
5 s
10, 20, 30, 60 s
36.67 ms
100 ms
200 ms
Trapezoidal
Rectangular
Cos
600 Hz and its integer multiples**
60 Hz and its integer multiples
50 Hz and its integer multiples
Automatically detects the power supply frequency andset
16.67 or 20 ms
50 Hz or 60 Hz and their integer multiples
10 Hz and its integer multiples
Fc = 5-Hz low-pass filter
Burnout
Detection
Cycle
200 ms
1 s*
1.67 ms
Measurement
interval
* When the measurement interval is 100 ms, burnout is detected in one channel per measurement interval.
Therefore, if measurement is started in a burnout condition or after a burnout occurs, burnout cannot be
detected for up to 10 measurements (approximately 1 second).
** Because the power supply frequency noise is not rejected, measured values may fluctuate particularly for
temperature measurements using thermocouples. If this happens, make the measurement interval longer, or
use the 4-CH High-Speed Universal Input Module.
Reference junction compensation:
Switch between external and internal on each channel, remote RJC
function available (see page 4-3)
Reference junction compensation accuracy:
When measuring temperature greater than or equal to 0°C and when the
temperature of the input terminal is balanced
 TypeR,S,W:±1°C
 TypeK,J,E,T,N,L,U:±0.5°C
Type N(AWG14), PLATINEL, NiNiMo, WRe3-25,
 W/WRe26:±1°C
 Note:Theinternalreferencejunctioncompensationisxedto0°Cfortype
B and PR40-20
4.5 10-CH, Medium-Speed Universal Input Module Specifications