EasyManuals Logo

YOKOGAWA MX100 User Manual

YOKOGAWA MX100
126 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #98 background imageLoading...
Page #98 background image
4-14
IM MX100-01E
Maximum input voltage:
DC voltage at 1-V range or less, TC, RTC, and DI (contact): VDC
(continuous)
Othermeasurementranges:±120VDC(continuous)
Normal-mode voltage:
DC voltage, TC, DI (LEVEL): 1.2 times the range rating or less
(50/60 Hz, peak value including the signal component)
RTD100Ω:50mVpeak
RTD10Ω,25Ω,50Ω:10mVpeak
Normal-mode rejection ratio:
For integration time of 16.67 ms or more: 40 dB or more (50/60
Hz±0.1%)
For integration time of 1.67 ms: 50/60 Hz is not rejected
The RTD ranges indicate the voltage conversion value when
measurement current applied.
Common-mode voltage:
600 VACrms (50/60 Hz), reinforced (double) insulation
Common-moderejectionratio(50/60Hz±0.1%,500Ωunbalanced,betweentheminus
terminal and ground)
For integration time is 16.67 ms or more: 120 dB or more
For integration time is 1.67 ms or more: 80 dB or more
The RTD ranges indicate the voltage conversion value when
measurement current applied.
Common-mode voltage between channels:
120 VACrms (50/60 Hz)
Noise rejection: Rejection by the integrating A/D converter and the use of low pass
lters
Inputresistance: DCvoltageat1Vrangeorless,TCrange:10MΩormore
DCvoltageat2Vrangeormore:Approx.1MΩ
Insulationresistance: 20MΩormore(500VDC)betweentheinputandground
Input bias current: 10 nA or less (except for burnout setting)
Withstand voltage: 1000 VAC (50/60 Hz) for one minute between input terminals
3700 VAC (50/60 Hz) for one minute between the input terminal
and earth terminal
Input signal source resistance:
DCvoltageandTC:2kΩorless
RTD50Ωand100Ωsystems:10Ωorlesspercable
RTD10Ωand25Ωsystems:1Ωorlesspercable
Thermocouple burnout:
Detectionataspecieddetectionintervalpermeasurement
interval and detection within the thermocouple range (detection
ON/OFF possible)
Up/Down setting is possible
2kΩorless:normal,200kΩormore:linebroken
(Shunt capacity of 0.01 µF or less), detection current of
approximately 10 µA, and detection time of approximately 2 ms
Shunt capacity during RTD: 0.01 mF or less
Power consumption: Approximately 1.2 W
External dimensions: Approximately 57 (W) × 131 (H) × 151 (D) mm (including the
terminal cover)
Weight: Approximately 0.5 kg
Terminal type: Clamp, terminal board is detachable
Applicable wire size: 0.14 to 1.5 mm
2
(AWG26 to 16)
4.5 10-CH, Medium-Speed Universal Input Module Specifications

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the YOKOGAWA MX100 and is the answer not in the manual?

YOKOGAWA MX100 Specifications

General IconGeneral
BrandYOKOGAWA
ModelMX100
CategoryData Loggers
LanguageEnglish

Related product manuals