Ametek 3050-RM

To Next Page

To Previous Page

Figure 4-2.

3050-RM sample system.

Figure 4-3.

Sensor removal in 3050-RM.

Moisture Generator

PN 305892901, Rev S

Maintenance and Troublshooting | 4-5

Main Page

Table of Contents3
Safety Notes7
Electrical Safety8
Grounding8
Sample Gas8
Personnel and Equipment Safety Information9
Special Warnings and Information11
Equipment Used in Class I, Division 2 Hazardous Locations11
Dryer Warning11
Electromagnetic Compatibility (EMC)12
Warning Labels13
Environmental Information - WEEE13
Overview15
Controller/Communications16
Contact Closure Signals17
System Alarm17
Moisture Concentration Alarm17
Data Valid17
Moisture Sensor18
Quartz Crystal Microbalance (QCM)18
Gas Measurement Cycle18
Gas Flow19
Sample System19
Sample Flow20
Solenoid Valves21
Verifying the Analyzer22
Changing Gases22
Dew/Frost Point Measurements23
Calculation of Dewpoint Values for Hydrocarbon Streams23
Installation and Start-Up25
Safety Considerations25
Pre-Installation Requirements26
Personnel Technical Level Required for Installation26
Analyzer Requirements26
Space Requirements26
Unpacking and Inspecting the Equipment28
Tools, Equipment, and Supplies Required for Installation28
Electrical Requirements29
Sample Temperature and Pressure Requirements29
Analyzer Installation30
User-Supplied Items Interconnect Wiring30
External Sample Tubing30
Rear Panel Connections and Interface Board31
Installing the Dryer33
Gas Connections35
Electrical Connections36
Voltage Selection36
Power Connection37
Communication Connections39
Signal Connections (4-20 Ma)40
Overview of the Keypad41
Function Keys41
Overview of Display43
Initial Start-Up44
Dry-Down Period44
Configuring the 3050-RM Analyzer for Serial Communications45
Protocol45
Special Addresses47
Address $F047
Defined Commands (Master to Slave)47
Echo (A)48
Bad Command (B)48
Acknowledge (C)48
Read Data (F)48
Start Verify (G)48
Write Data (H)49
Write Cell EEPROM (L)49
Quit (Q)49
Defined Responses (Slave to Master)50
Simple Acknowledge50
Acknowledge with Data50
Failure50
Variables Table51
Controller/Interface53
Working from the Built-In User Interface53
Verify Key55
Alarm Key56
Range Key57
Config Key58
Display58
Communication59
Sample Gas60
Clock62
Verify Schedule63
Production Codes64
Moisture Unit65
System Test66
Working from the AMETEK 3050 UHP Configurator Software67
UHP Configurator Software Installation67
Configuring the 3050-RM68
Working from the General Tab68
Saving Analyzer Configuration Settings70
Working from the Device Communication Tab71
Configuring Multiple Analyzers71
Changing Communication Parameters71
Saving Your Settings72
Working from the Setup Tab73
Working from the Schedule Tab75
Saving Your Settings77
Working from the Status Tab78
Working from the Monitor Tab79
Data Capture80
Maintenance and Troubleshooting81
Aftermarket Excellence and Long-Term Commitment to Safety and Quality82
3050-RM Analyzer Replacement Parts83
Servicing the 3050-RM Analyzer84
Sensor86
Removing the Sensor86
Installing the Sensor86
Mass Flow Meter87
Installing the Mass Flow Meter87
Moisture Generator89
Removing the Moisture Generator89
Installing the New Moisture Generator92
Solenoid Valves92
Installing the New Solenoid94
Dryers/Contaminant Traps95
Removing the Dryer95
Installing the New Dryer/Trap96
Maintenance of the Electronics Module97
Tools Required97
Procedure for Removing the Electronics Module97
Analog Interface Board99
Removing the Analog Interface Board99
Replacing the Analog Interface Board99
MCU Board100
Removing the MCU Board100
Replacing the MCU Board100
Reinstalling the Electronics Module101
Board Connections102
User Interface Board102
Alarm Messages103
Specifications107
Compatible Gases107
3050-RM Moisture Analyzer Specifications107
3050-RM Moisture Analyzer Approvals and Certifications108
Appendix A - Quick Reference Card109

Table of Contents

Related product manuals