Binder M 56 - UKCA Declaration of Conformity

To Next Page

To Previous Page

M (E3.1) 1/2023 page 128/136

23.2 UKCA Declaration of Conformity

Main Page

Table of Contents2
Safety6
Personnel Qualification6
Operating Manual6
Legal Considerations6
Intellectual Property7
Structure of the Safety Instructions7
Signal Word Panel7
Safety Alert Symbol8
Pictograms8
Word Message Panel Structure9
Localization / Position of Safety Labels on the Chamber9
Type Plate10
UKCA Label11
General Safety Instructions on Installing and Operating the Chambers11
Intended Use13
Foreseeable Misuse14
Residual Risks15
Operating Instructions16
Measures to Prevent Accidents16
Chamber Description17
Chamber Overview18
Chamber Rear19
Triangular Instrument Panel20
Main Power Switch (Sizes 260 and 720)20
Zero-Voltage Switching Contact20
Completeness of Delivery, Transportation, Storage, and Installation21
Unpacking, and Checking Equipment and Completeness of Delivery21
Guidelines for Safe Lifting and Transportation22
Storage22
Location of Installation and Ambient Conditions22
Installation24
Electrical Connection24
Connection to an Exhaust/Ventilation System (Optional)25
Inserting the Racks25
Functional Overview of the Mb2 Chamber Controller26
Operating Functions in Normal Display27
Display Views: Normal Display, Program Display, Chart-Recorder Display28
Controller Icons Overview29
Operating Modes31
Controller Menu Structure32
Main Menu33
Settings" Submenu34
Service" Submenu34
Principle of Controller Entries35
Performance During and after Power Failures35
Performance When Opening the Door36
Failsafe Function36
Start up36
Turning on the Chamber36
Controller Settings Upon Start up36
Loading37
Set-Point Entry in "Fixed Value" Operating Mode38
Set-Point Entry for Temperature and Fan Speed through the "Setpoints" Menu38
Adjusting the Air Flap Position through the "Setpoints" Menu39
Direct Setpoint Entry Via Normal Display40
Special Controller Functions Via Operation Lines41
Timer Program: Stopwatch Function42
Starting a Timer Program42
Performance During Program Delay Time42
Stopping a Running Timer Program43
Pausing a Running Timer Program43
Cancelling a Running Timer Program43
Performance after the End of the Program43
Time Programs44
Starting an Existing Time Program44
Performance During Program Delay Time45
Stopping a Running Time Program45
Pausing a Running Time Program45
Cancelling a Running Time Program45
Performance after the End of the Program45
Creating a New Time Program46
Program Editor: Program Management46
Deleting a Time Program47
Section Editor: Section Management48
Add a New Program Section49
Copy and Insert or Replace a Program Section49
Deleting a Program Section50
Value Entry for a Program Section51
Section Duration51
Set-Point Ramp and Set-Point Step52
Special Controller Functions Via Operation Lines53
Setpoint Entry for Temperature and Fan Speed, Setting the Air Flap Position54
Tolerance Ranges55
Repeating One or Several Sections Within a Time Program55
Saving the Time Program56
Week Programs57
Starting an Existing Week Program57
Cancelling a Running Week Program57
Creating a New Week Program58
Program Editor: Program Management59
Deleting a Week Program60
Section Editor: Section Management61
Add a New Program Section62
Copy and Insert or Replace a Program Section62
Deleting a Program Section63
Value Entry for a Program Section63
Set-Point Ramp and Set-Point Step Modes63
Weekday64
Start Time64
Setpoint Entry for Temperature and Fan Speed, Setting the Air Flap Position65
Special Controller Functions Via Operation Lines65
Notification and Alarm Functions66
Notification and Alarm Messages Overview66
Notifications66
Alarm Messages67
State of Alarm67
Resetting an Alarm, List of Active Alarms68
Tolerance Range Settings68
Activating / Deactivating the Audible Alarm (Alarm Buzzer)69
Overtemperature Protection70
Overtemperature Protective Device Class 170
Message and Measures in the State of Alarm70
Overtemperature Safety Controller Class 2 / 3.171
Selecting between Safety Controller Class 2 (Temperature Limiter) or Class 3.172
Safety Controller Mode72
Setting the Safety Controller73
Message and Measures in the State of Alarm73
Function Check74
Zero-Voltage Relay Alarm Contact75
User Management76
Authorization Levels and Password Protection76
Log in79
Log out80
User Change80
Password Assignment and Password Change81
Password Change81
Deleting the Password for an Individual Authorization Level83
New Password Assignment for "Service" or "Admin" Authorization Level When the Password Function was Deactivated84
Activation Code85
General Controller Settings86
Selecting the Controller's Menu Language86
Setting Date and Time86
Selecting the Temperature Unit88
Display Configuration88
Adapting the Display Parameters88
Touchscreen Calibration89
Network and Communication90
Ethernet90
Configuration90
Display of the MAC Address91
Web Server91
E-Mail92
USB Menu: Data Transfer Via USB Interface93
General Information94
Service Contact Page94
Current Operating Parameters94
Event List95
Technical Chamber Information95
Chart Recorder Display96
Views96
Show and Hide Legend96
Switch between Legend96
Show and Hide Specific Indications97
History Display97
Setting the Parameters100
Options101
APT-COM™ 4 Multi Management Software (Option)101
Object Temperature Display with Flexible Pt100 Temperature Sensor (Option)101
Object Temperature Control with Flexible Pt100 Temperature Sensor (Option)102
Analog Output for Temperature (Option)103
HEPA Fresh Air Filter (Option)103
Mostly Gas-Tight Version (Option)103
Inert Gas Connection with Mostly Gas-Tight Version (Option)104
Cleaning and Decontamination106
Cleaning106
Decontamination / Chemical Disinfection108
Maintenance and Service, Troubleshooting, Repair, Testing109
General Information, Personnel Qualification109
Maintenance Intervals, Service109
Simple Troubleshooting110
Sending the Chamber Back to BINDER Gmbh112
Disposal113
Disposal of the Transport Packing113
Decommissioning113
Disposal of the Chamber in the Federal Republic of Germany113
Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany114
Disposal of the Chamber in Non-Member States of the EU116
Technical Description116
Factory Calibration and Adjustment116
Definition of Usable Volume116
Over Current Protection117
M Technical Data117
Equipment and Options (Extract)119
Accessories and Spare Parts (Extract)120
Dimensions Size 56121
Dimensions Size 115122
Dimensions Size 260123
Dimensions Size 720124
Certificates and Declarations of Conformity125
EU Declaration of Conformity125
UKCA Declaration of Conformity128
Certificate for the GS Mark of Conformity of the "Deutsche Gesetzliche Unfallversicherung E.V." (German Social Accident Insurance) DGUV129
Contamination Clearance Certificate131
For Chambers Located Outside the USA and Canada131
For Chambers Located in the USA and Canada134

Binder M 56 - UKCA Declaration of Conformity

Table of Contents

Related product manuals