BW Technologies MicroDock II - Microdock II Base Station and Docking Modules

100 pages

Save Page as PDF

To Next Page

To Previous Page

MicroDock II

User Manual

MicroDock II Base Station and Docking Modules

Figure 1. MicroDock II Base Station and Docking Modules

To connect additional docking modules and to correctly insert detectors into docking modules, refer to Installation.

Main Page

Default Chapter1
- User Manual1
Table2
Limited Warranty and Limitation Liability2
- Table of Contents3
- List of Figures9
Introduction11
Contacting BW Technologies by Honeywell12
Safety Information - Read First12
- International Symbols14
Title Figure14
Getting Started15
Microdock II Base Station and Docking Modules16
- Parts of the Microdock II Base Station and Docking Module17
- The Microdock II Base Station and Docking Module17
Display Elements18
Pushbuttons18
- Docking Module Pushbuttons18
- Base Station Pushbuttons19
Installation20
- Base Station Connections20
- Inserting the Gasalertmicro 5/PID/IR27
Adding Another Docking Module37
- Torque Specifications37
Title41
- Initializing the New Docking Module41
- Defining Pump Speed41
Mounting the Microdock II42
- Mounting the Microdock II43
Changing Dip Switch Settings (Gasalertclip Extreme Only)44
- Dip Switch Settings44
- Changing Dip Switch Settings44
Using the Base Station47
- Confirming Inlet Setup47
- Activating the Base Station47
- Self-Test47
- Deactivating the Base Station48
User Options Menu49
- Time/Date49
- Inlet Setup50
  - Gas Type51
- Inlets 2-5 - Available Gas Types51
Results History61
Reconfiguring the Detector (Not Applicable to the Gasalertclip Extreme)63
Gas Conflicts64
Title65
- Abort Option65
- Conflicts65
  - Base Station Selects the Gas Inlet66
  - User Selects Gas Inlet66
- Not Found67
Accessing the MMC/SD Card During a Test68
Order of Gases Applied for Bump Tests and Calibrations69
- Gas Type Application Table70
- Gas Application Rules71
Bump Test72
- Bump Test Results75
Calibration77
- Guidelines77
- Calibration Procedure (All Models Excluding the Gasalertclip Extreme)78
  - Gasalertmicro 5 IR with CO 2 Sensor79
- Calibration Results80
Data Transfer (Gasalert Extreme, Gasalertmicroclip, Gasalertmax XT, and Gasalertquattro Only)82
- Transferring Datalogs82
  - Maximum Datalog Storage Capacity83
- Automatic Datalog Download (Gasalertmicroclip, Gasalertmax XT, and Gasalertquattro Only)83
  - Using the IR Link83
  - Using the Microdock II83
Title85
Base Station MMC/SD Card85
- Event Logging85
- Inserting/Replacing a MMC/SD Card86
- Accessing Test Results86
  - PC Requirements86
Charging the Battery Pack (Excluding Gasalert Extreme and Gasalertclip Extreme)87
- Charger/Battery Pack Guidelines87
- Charging Different Detectors Together87
- Charging Procedure88
- Charger Status LED88
Maintenance89
- Battery Pack Storage89
  - Gasalertmicro and Gasalertmicro 5/PID/IR89
  - Gasalertmicroclip89
Troubleshooting90
- Troubleshooting Tips90
Replacement Parts and Accessories97
Specifications98
- Charger Specifications99

BW Technologies MicroDock II - Microdock II Base Station and Docking Modules

Table of Contents

Other manuals for BW Technologies MicroDock II