Cisco ASA Series

To Next Page

To Previous Page

1-67

Cisco ASA Series CLI Configuration Guide

Chapter 1 Configuring a Cluster of ASAs

Configuration Examples for ASA Clustering

Link or device failure is handled with the same principle. You may end up with a less-than-perfect load

balancing situation. The following figure shows a 4-unit cluster with a single link failure on one of the

units.

333217

ASA1

ASA2

ASA3

ASA4

Main Page

Cisco ASA Series CLI Configuration Guide1
About This Guide3
Glossary5
Index29
Getting Started with the ASA61
- Introduction to the Cisco ASA63
- Configuring the Switch for Use with the ASA Services Module95
- Getting Started109
- Configuring the Transparent or Routed Firewall137
- Managing Feature Licenses163
Configuring High Availability and Scalability219
- Configuring Multiple Context Mode221
- Configuring a Cluster of ASAs265
- Information About Failover337
- Configuring Active/Standby Failover359
- Configuring Active/Active Failover377
Configuring Interfaces403
- Starting Interface Configuration (ASA 5510 and Higher)405
- Starting Interface Configuration (ASA 5505)443
- Completing Interface Configuration (Routed Mode)457
- Completing Interface Configuration (Transparent Mode)477
Configuring Basic Settings499
- Configuring Basic Settings501
- Configuring DHCP517
- Configuring Dynamic DNS527
Configuring Objects and Access Lists533
- Configuring Objects535
- Information About Access Lists555
- Adding an Extended Access Control List559
- Adding an EtherType Access List573
- Adding a Standard Access Control List579
- Adding a Webtype Access Control List585
- Configuring Logging for Access Lists593
  - Configuring Logging for Access Lists593
  - Managing Deny Flows597
Configuring IP Routing601
- Routing Overview603
- Configuring Static and Default Routes615
- Defining Route Maps625
- Configuring OSPF633
- Configuring EIGRP681
- Configuring RIP701
- Configuring Multicast Routing713
- Configuring IPv6 Neighbor Discovery729
Configuring Network Address Translation745
- Information About NAT747
- Configuring Network Object NAT781
- Configuring Twice NAT813
Configuring AAA Servers and the Local Database845
- Configuring AAA Servers and the Local Database847
- Configuring the Identity Firewall881
- Configuring the ASA to Integrate with Cisco TrustSec905
- Configuring Digital Certificates937
Configuring Access Control981
- Configuring Access Rules983
- Configuring Management Access995
- Configuring AAA Rules for Network Access1029
- Configuring Web Cache Services Using WCCP1055
Configuring Service Policies Using the Modular Policy Framework1061
- Configuring a Service Policy Using the Modular Policy Framework1063
- Configuring Special Actions for Application Inspections (Inspection Policy Map)1085
Configuring Application Inspection1093
- Getting Started with Application Layer Protocol Inspection1095
- Configuring Inspection of Basic Internet Protocols1107
- Configuring Inspection for Voice and Video Protocols1143
- Configuring Inspection of Database and Directory Protocols1173
- Configuring Inspection for Management Application Protocols1179
Configuring Unified Communications1191
- Information About Cisco Unified Communications Proxy Features1193
- Configuring the Cisco Phone Proxy1199
- Configuring the TLS Proxy for Encrypted Voice Inspection1253
- Configuring Cisco Mobility Advantage1271
- Configuring Cisco Unified Presence1285
- Configuring Cisco Intercompany Media Engine Proxy1305
Configuring Connection Settings and QoS1333
- Configuring Connection Settings1335
- Configuring QoS1351
- Troubleshooting Connections and Resources1371
  - Testing Your Configuration1371
  - Monitoring Per-Process CPU Usage1377
Configuring Advanced Network Protection1379
- Configuring the ASA for Cisco Cloud Web Security1381
- Configuring the Botnet Traffic Filter1407
- Configuring Threat Detection1429
- Using Protection Tools1449
- Configuring Filtering Services1457
Configuring Modules1475
- Configuring the ASA IPS Module1477
- Configuring the ASA CX Module1505
- Configuring the ASA CSC Module1529
Configuring VPN1549
- Configuring IPsec and ISAKMP1551
- Configuring L2TP over IPsec1593
- Setting General VPN Parameters1613
- Configuring Connection Profiles, Group Policies, and Users1635
- Configuring IP Addresses for VPNs1737
- Configuring Remote Access IPsec VPNs1745
- Configuring Network Admission Control1761
- Configuring Easy VPN Services on the ASA 55051779
- Configuring the PPPoE Client1791
- Configuring LAN-to-LAN IPsec VPNs1797
- Configuring Clientless SSL VPN1809
- Configuring AnyConnect VPN Client Connections1929
- Configuring AnyConnect Host Scan1957
Configuring Logging, SNMP, and Smart Call Home1965
- Configuring Logging1967
- Configuring NetFlow Secure Event Logging (NSEL)1989
- Configuring SNMP2003
- Configuring Anonymous Reporting and Smart Call Home2037
System Administration2059
- Managing Software and Configurations2061
- Troubleshooting2091
Reference2099
- Using the Command-Line Interface2101
- Addresses, Protocols, and Ports2109
- Configuring an External Server for Authorization and Authentication2125

Table of Contents

Other manuals for Cisco ASA Series

Related product manuals