Cisco Catalyst 3560X-24P User Manual

2-431
Catalyst 3750-X and 3560-X Switch Command Reference
OL-21522-02
Chapter 2 Catalyst 3750-X and 3560-X Switch Cisco IOS Commands
permit (IPv6 access-list configuration)
permit (IPv6 access-list configuration)
Use the permit IPv6 access list configuration command on the switch stack or on a standalone switch to
set permit conditions for an IPv6 access list. Use the no form of this command to remove the permit
conditions.
Note This command is not supported on switches running the LAN base feature set.
permit {protocol} {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator
[port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address}
[operator [port-number]] [dscp value] [fragments] [log] [log-input] [routing] [sequence
value] [time-range name]
no permit {protocol} {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator
[port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address}
[operator [port-number]] [dscp value] [fragments] [log] [log-input] [routing] [sequence
value] [time-range name]
Note Although visible in the command-line help strings, the flow-label and reflect keywords are not
supported.
Internet Control Message Protocol
permit icmp {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator
[port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address}
[operator [port-number]] [icmp-type [icmp-code] | icmp-message] [dscp value] [log]
[log-input] [routing] [sequence value] [time-range name]
Transmission Control Protocol
permit tcp {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator
[port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address}
[operator [port-number]] [ack] [dscp value] [established] [fin] [log] [log-input] [neq {port |
protocol}] [psh] [range {port | protocol}] [rst] [routing] [sequence value] [syn] [time-range
name] [urg]
User Datagram Protocol
permit udp {source-ipv6-prefix/prefix-length | any | host source-ipv6-address} [operator
[port-number]] {destination-ipv6-prefix/prefix-length | any | host destination-ipv6-address}
[operator [port-number]] [dscp value] [log] [log-input] [neq {port | protocol}] [range {port |
protocol}] [routing] [sequence value] [time-range name]
Note Although visible in the command-line help strings, the flow-label and reflect keywords are not
supported.
This command is available only if your switch has a switch database management (SDM) dual IPv4 and
IPv6 template configured.

Cisco Catalyst 3560X-24P Specifications

General

Device Type	Switch
Enclosure Type	Rack-mountable
Ports	24
Power over Ethernet (PoE)	Yes
Stacking	Yes
RAM	512 MB
Flash Memory	128 MB
Power Device	Internal power supply
Voltage Required	100-240V AC
Operating Temperature	32 to 113°F (0 to 45°C)
Jumbo Frame Support	Yes
Routing Protocol	OSPF, RIP, EIGRP
Remote Management Protocol	SNMP, SSH, Telnet
Features	Quality of Service (QoS), VLAN support, Access Control Lists (ACLs)
Compliant Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z
Operating Humidity	10% to 90% non-condensing
Management	SNMP
Model	Cisco Catalyst 3560X-24P
Uplink Ports	4
MAC Address Table Size	16K