Develop ineo+ 25 - User Manual

Other manuals for Develop ineo+ 25

Product Guide24 pages

Questions and Answers

M
Michael MatthewsAug 13, 2025
Why does my Develop ineo+ 25 All in One Printer say [Toner Low] so early?
- H
  hernandezgeorgeAug 13, 2025
  If your Develop All in One Printer displays the message [Toner Low] much sooner than expected, one of the toner cartridges might be defective. Remove the toner cartridges and check them for damage. Replace any damaged cartridges. Also, heavy toner coverage during printing could be the reason. Refer to the specifications in the Appendix.
M
Matthew AguilarAug 21, 2025
What to do if the media mis-feed message stays on Develop ineo+ 25 All in One Printer?
- H
  Haley EdwardsAug 21, 2025
  If the media mis-feed message stays on your Develop All in One Printer, either the front cover needs to be opened and closed again to reset the machine, or some media remains misfed in the machine. Open and close the front cover again. Also, double-check the media path to ensure all misfed media has been removed.
M
Matthew CruzAug 25, 2025
Why Develop ineo+ 25 power is not on?
- F
  fsmithAug 25, 2025
  If your Develop All in One Printer is not turning on, it could be due to a few reasons: * The power cord is not correctly plugged into the outlet. Turn off the machine, ensure the cord is properly plugged in, and then turn the machine back on. * There's an issue with the outlet. Plug another appliance into the outlet to test it. * The power switch is not correctly turned on. Turn the power switch off (O position), then turn it back to the on (I position). * The machine is connected to an incompatible power source. Use a power source that matches the machine's specifications.
T
Thomas DorseyAug 28, 2025
What to do if media is misfed in the ADF of Develop ineo+ 25 All in One Printer?
- I
  isaac48Aug 28, 2025
  If your Develop All in One Printer is misfeeding media in the ADF, it could be because the loaded document does not meet the specifications, exceeds the maximum capacity, or the document guides were not slid against the edges of the document. Load the correct document, ensuring it doesn't exceed the maximum capacity. Slide the document guides against the edges of the document.
L
lisa50Sep 1, 2025
Why are there duplex mis-feeds in my Develop ineo+ 25 All in One Printer?
- S
  Scott MorenoSep 1, 2025
  Duplex mis-feeds in your Develop All in One Printer can occur if unsupported media is used. Use DEVELOP-approved media. Also, media may still be misfed. Check the media path inside the duplex again to ensure that you have removed all of the misfed media.
K
Kimberly WillisSep 4, 2025
How to prevent several sheets going through Develop All in One Printer together?
- S
  stephaniewareSep 4, 2025
  If your Develop All in One Printer is feeding several sheets together, it may be because the front edges of the media are not even, or the media is moist from humidity. Remove the media and even up the front edges, then reload it. If the media is moist, replace it with new, dry media.
T
Taylor MitchellSep 8, 2025
Why can't I print the machine status list on my Develop ineo+ 25 All in One Printer?
- J
  John CrawfordSep 9, 2025
  If you cannot print the machine status list on your Develop All in One Printer, the tray might be empty, or there may be a media mis-feed. Check that at least Tray 1 is loaded with media, in place, and secure. Clear any media misfeeds.
B
Brian KingNov 16, 2025
Why is media misfeeding in my Develop ineo+ 25?
- P
  perryleahNov 16, 2025
  If your Develop All in One Printer is misfeeding media, it could be due to several reasons: * The media is not correctly positioned in the tray: Reposition the media properly. * Too many sheets in the tray: Remove the excess media. * Media guides not adjusted: Adjust the media guides to match the media size. * Warped or wrinkled media: Smooth out the media or replace it. * Moist media: Replace it with new, dry media. * Envelopes loaded in Tray 2 or 3: Load envelopes in Tray 1 only. * Special media in Tray 3: Load special media in Tray 1 or 2. * Custom-sized media in Tray 3: Load custom-sized media in Tray 1 or 2. * Incorrectly loaded label sheets: Load according to manufacturer's instructions. * Envelopes facing the wrong way: Load envelopes in Tray 1 with the flaps fa...